Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

SPOS

Created by: makaveli at: 6/10/2011 4:40 PM (8 Replies)

Rating (0)

Thanks 0

9 Entries

6/10/2011 4:40 PM	Rate (0)
makaveli Posts: 259 Rating: (5)	Hi, I have three the same machine with second spindle use for milling. When i setup angle with SPOS command on two machine is not possible to move/rotate this spindle by hand but on one you can rotate it very easy.... Any advise... With regards, makaveli
makaveli Posts: 259 Rating: (5)
Suggestion To thank Quote Answer

6/10/2011 4:45 PM	Rate (0)
VENKATESH Posts: 11 Rating: (0)	Hello... What Control is this ??? can you use M19 and check.... can u rotate the spindle and check feedback is coming..... Regards, Venkatesh
VENKATESH Posts: 11 Rating: (0)
Suggestion To thank Quote Answer

6/10/2011 5:03 PM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi After you position the spindle with SPOS and move the spindle with hand do you receive a alarm? Good luck Nit

Suggestion To thank Quote Answer

6/10/2011 10:18 PM	Rate (0)
makaveli Posts: 259 Rating: (5)	Hi, This is in 840D pl. It is with safety function on so when you move with hand alarm appears. M19 and Spos are the same function. With regards, makaveli
makaveli Posts: 259 Rating: (5)
Suggestion To thank Quote Answer

6/11/2011 6:14 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi Sorry but M19 and SPOS is not the same function. M19 is positioning the spindle at the spindle reference point and SPOS can posion the spindle at any angle. Good luck Nit

Suggestion To thank Quote Answer

6/11/2011 8:26 AM	Rate (0)
makaveli Posts: 259 Rating: (5)	Hi, You have right. But of course with M19 you cannot specify position. But this is not important. What you think what can cause my problem. With regards, makaveli
makaveli Posts: 259 Rating: (5)
Suggestion To thank Quote Answer

6/11/2011 8:39 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi I don't see where the problem is since on this machine you have safety function activated so it is normal that the spindle driver it is not enabled with the doors open (I assume because other way you wouldn't be able to rotate the spindle with hand). Good luck Nit

Suggestion To thank Quote Answer

6/11/2011 9:15 AM	Rate (0)
makaveli Posts: 259 Rating: (5)	Hi, This is big machine and door always thing that are closed. So this isn't a problem. I told you before on two others the same machine is not possible rotate by hand and on this without problem and on all are the same conditions. With regards, makaveli
makaveli Posts: 259 Rating: (5)
Suggestion To thank Quote Answer

6/11/2011 9:45 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi Maybe other machines doesn't have safety system or it may be made different. Generally with the safety system active, all the drives are disabled and the system is put in following mode (that's way you receive an alarm when you rotate the spindle by hand) and so the machine can't start to move even if it is a bad command or a malfunction in the control system. This are done separately from the system. Good luck Nit

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on