SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

New in STL

12/21/2006 7:26 AM	Rate (0)
JLarsen Posts: 6 Rating: (1)	I have programmed a lot i Siemens Step7 in LAD and FBD, but now I have to do a project in STL. Is there any tutorials, or do anyone have some documents or links describing the general "rules" for programming in STL?
JLarsen Posts: 6 Rating: (1)
Suggestion To thank Quote Answer

12/21/2006 11:53 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 1/9/2026 Posts: 9104 Rating: (1202)	Hi JLarsen, Perhaps the following manual is usefull: http://support.automation.siemens.com/WW/view/en/18653496 Best regards, Wizard

Suggestion To thank Quote Answer

12/22/2006 7:32 AM	Rate (0)
JLarsen Posts: 6 Rating: (1)	Thanks! Just what I was looking for.[:)] Best Regards JLarsen
JLarsen Posts: 6 Rating: (1)
Suggestion To thank Quote Answer

12/27/2006 1:27 AM	Rate (0)
Tennessee Chris Posts: 4 Rating: (0)	you can program in ladder and then veiw in stl. if it must be programmed in stl just print and start new putting it back in.
Tennessee Chris Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

1/5/2007 1:55 PM	Rate (0)
Morten Bronze Member Joined: 9/27/2005 Last visit: 12/16/2025 Posts: 203 Rating: (32)	Hallo JLarsen, look in your STEP 7-folder: SIMATIC -> Documentation -> English There you find the manual explaining programming with STL. Greetings Morten

Suggestion To thank Quote Answer

1/6/2007 6:39 PM	Rate (0)
Late Platinum Member Joined: 1/7/2006 Last visit: 5/11/2025 Posts: 2705 Rating: (321)	Hi J, Try the help in STEP7 to find all commands that can be used in STL, the hole bunch is to find in the help of STEP7. [:)] Reading handbooks is most of the time for programming not that usefull, starting and then using the help is most of the time better. This is only when you already have enough experience with STEP7 in LAD or FBD. [:o]
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

1/8/2007 1:47 PM	Rate (1)
Denilson Pegaia Diamond Member Joined: 9/23/2005 Last visit: 1/12/2026 Posts: 4444 Rating: (1487)	Hi, just a Tip: if you have a doubt about a logic, that can be done in LAD, make it first in LAD, so change the view to STL. That works as simple samples.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

Share this page:

Share this page on...