SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

CU320 Confuiguration

2/12/2012 4:27 PM	Rate (0)
Ahmed Experienced Member Joined: 2/20/2007 Last visit: 11/19/2024 Posts: 122 Rating: (2)	Dear all, In my configuration,I have one SLM and 1 Motor module ( 1000 kW) for stand Motor in Mill. Motor module wil be configured in vector mode using SMC 30. Due to analog outputs i have used TM31 also. Please confirm me whether one CU320-2 DP is sufficient for 1 SLM, 1 MM with SMC 30 and TM31. or do i have to consider 2 CU 320??? Thanks in Advance Ahmed

Suggestion To thank Quote Answer

2/12/2012 5:38 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/19/2025 Posts: 22816 Rating: (3073)	Hello, one Cu320-2 is enough for this configuration. Regards Christoph

Suggestion To thank Quote Answer

2/13/2012 5:58 AM	Rate (0)
Ahmed Experienced Member Joined: 2/20/2007 Last visit: 11/19/2024 Posts: 122 Rating: (2)	Thanks Chris Is there anydocumentation for selection of CU 320 depending upon the application.w.r.t loading of CU320 or use of Enhancement CFC?? For eg..for 1 CU320 can support 4 MoMo but if all 4 should run in v/f mode. If we have to use 4 MoMo in vector mode then we have to go for 2 CU320. and if the application is much more advanced like using basic positioner we have to select 1 CU320 for 1 MoMo. Thanks in Advance Ahmed.

Suggestion To thank Quote Answer

2/13/2012 1:31 PM	Rate (0)
DenisMor Posts: 344 Rating: (50)	Sinamics Sizer is the program for selecting motors, Sinamics drives and control units based on requirements you are talking about. It is not available for download from the web, but is available free from any Siemens rep or distributor.
DenisMor Posts: 344 Rating: (50)
Suggestion To thank Quote Answer

2/13/2012 1:48 PM	Rate (0)
Ahmed Experienced Member Joined: 2/20/2007 Last visit: 11/19/2024 Posts: 122 Rating: (2)	Dear Denis I know that we have sizer software for deciding the CU320 configuration but additionally are there any manual/documentation deciding the criteria apart from sizer software. Thanks in Advance Ahmed

Suggestion To thank Quote Answer

2/13/2012 10:02 PM	Rate (0)
umencho Grandmaster Joined: 3/21/2006 Last visit: 10/16/2025 Posts: 10239 Rating: (1183)	click

Suggestion To thank Quote Answer

2/14/2012 11:17 AM	Rate (0)
Bead Posts: 5 Rating: (0)	It would be sufficient for you below manual. "SINAMICS S120 Commissioning Manual" you can find concerned configurations on27 ~ 41 page. that manual file is too large to uploadon this board. Regards, Brian
Bead Posts: 5 Rating: (0)	Last edited by: Bead at: 2/14/2012 11:18 AM
Suggestion To thank Quote Answer

Share this page:

Share this page on...