Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Reset Sinamics Integrated Fault Through ST

Created by: AmazingTrans at: 2/14/2012 8:21 PM (7 Replies)

Rating (0)

Thanks 0

8 Entries

2/14/2012 8:21 PM	Rate (0)
AmazingTrans Posts: 31 Rating: (0)	Hi there, I have sinamics Integrated fault in my alarm view, and I always click on the acknowledge all button on simotion scout. Right now I want to programatically program it so I can have the HMI button to act as the ack all button. What command should I use to acknowledge all sinamics integrated faults? I tried _resetTechnologicalErrors in the ladder and it did not reset it. Any ideas? Thanks! AmazingTrans
AmazingTrans Posts: 31 Rating: (0)	Last edited by: AmazingTrans at: 2/14/2012 8:34 PM
Suggestion To thank Quote Answer

2/14/2012 9:02 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22443 Rating: (3029)	Hello, which fault do you have and on which DriveObject? Normaly the DriveFaults acknowledge is doing by the TechnologicalObject which is connected to the DriveObject. There is only the systemfunction _resetDriveObjectFault for the DO1 (ControlUnit)faults. Regards Christoph

Suggestion To thank Quote Answer

2/14/2012 9:32 PM	Rate (0)
AmazingTrans Posts: 31 Rating: (0)	We have an encoder object that couldn't be reset using _resetTechnologicalErrors. Any ideas why? or what does the _resetTechnologicalErrorsactually resets? ThanksChris.
AmazingTrans Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

2/14/2012 9:43 PM	Rate (0)
AmazingTrans Posts: 31 Rating: (0)	I triedsystemfunction _resetDriveObjectFault and reset the encoder object which is on address 448 (448 ..451), PZD message frames. It says error 8090 : Job Aborted possible cause: - logical address does not exist - Logical address exist but is not the address of a drive object. Any more ideas? Thanks.
AmazingTrans Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

2/15/2012 9:34 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22443 Rating: (3029)	Hello, have you configure a Encoder or Axis in SImotion on the DO Encoder? The function _resetdriveobjectfault only work for Faults on the ControlUnit of the SINAMICS. Regards Christoph

Suggestion To thank Quote Answer

2/15/2012 2:55 PM	Rate (0)
AmazingTrans Posts: 31 Rating: (0)	Christoph, The DO Encoder is tied to the Handwheel encoder on a SMC30. But on the other hand, when we triggered the p2102 on the control unit manually, it resets all the drive object. Where as when we try to trigger the _resetdriveobjectfault on the CU, it does not trigger it because the CU is not faulted but the DO Encoder is faulted instead. Any ideas? Regards, Johnny
AmazingTrans Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

2/16/2012 12:47 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/11/2024 Posts: 22443 Rating: (3029)	Hello, have you any TO in Simotion (axis or so) which ist connected to this SINAMICS? Or have the ControlUnit a logical Adress ? Regards Christoph
	Last edited by: ChristophD at: 2/16/2012 12:48 PM
Suggestion To thank Quote Answer

2/16/2012 9:42 PM	Rate (0)
AmazingTrans Posts: 31 Rating: (0)	ChristoD, Yes we have the DOin sinamics tie to the TO in simotion. And the CU has a logical address.
AmazingTrans Posts: 31 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_General

Follow us on