SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Set-Point for I/O´s Sinamics G120

Created by: Urantia at: 12/6/2012 12:40 AM (5 Replies)

Rating (0)

Thanks 0

6 Entries

12/6/2012 12:40 AM	Rate (0)
Urantia Experienced Member Joined: 10/23/2009 Last visit: 7/29/2025 Posts: 118 Rating: (0)	Helllo all, I'm taking control with SINAMICS G120 (CU320) speed set point, I'm doing through analog input. The problem I have is that after the ramp generator frequency is always zero, even though at the beginning I have a frequency nonzero. I have enabled all ratings, as shown in Fig. Thank you very much for the help Attachment Ramp.jpg (284 Downloads)

Suggestion To thank Quote Answer

12/6/2012 4:09 PM	Rate (0)
Graeme Platinum Member Joined: 6/4/2008 Last visit: 11/25/2025 Posts: 1521 Rating: (327)	Hi, your picture is practically unreadable, can you upload an archive of your drive? It is bound to be one of your enables is missing (Could be internal). Regards, Graeme

Suggestion To thank Quote Answer

12/6/2012 4:30 PM	Rate (0)
Urantia Experienced Member Joined: 10/23/2009 Last visit: 7/29/2025 Posts: 118 Rating: (0)	Hi Graeme, Attached the picture again, pay atention to red box, Thanks in advance! Attachment Ramp.jpg (268 Downloads)

Suggestion To thank Quote Answer

12/6/2012 4:34 PM	Rate (0)
Urantia Experienced Member Joined: 10/23/2009 Last visit: 7/29/2025 Posts: 118 Rating: (0)	Attached the program, Greetings! Attachment TubesaMolinoV1.zip (260 Downloads)

Suggestion To thank Quote Answer

12/6/2012 10:05 PM	Rate (0)
Graeme Platinum Member Joined: 6/4/2008 Last visit: 11/25/2025 Posts: 1521 Rating: (327)	Hi, several things, as you are connected via starter, the OFF2 bit r19.0 (Red button on the BOP) will not be set and will hold off the start command. So temporarily disable this by setting P845 = 1. If you look closely at the graphic (I can also just make it out on your first image you sent), even when all the "LED's" are lit, the switch is still in the OFF (0) position, this generally means that there is an internal bit that is inhibiting the start command. I have highlighted this with a Yellow Oval. If you take a look at the "Drive Enables" in the Control/Status Word section under the Diagnostics menu, this will tell you what is still missing when you are trying to run. Regards, Graeme Attachment Ramp (1).jpg (264 Downloads)

Suggestion To thank Quote Answer

12/7/2012 8:54 PM	Rate (0)
Urantia Experienced Member Joined: 10/23/2009 Last visit: 7/29/2025 Posts: 118 Rating: (0)	Hi Graeme. In addition to your comments, I realized that the signal from the potentiometer connected to the analog input of the CU320, ranged far is oscilacón was not perceived on my PC, but if it was perceived in the MOP panel. This did not allow the output frequency of the filter. I appreciate your help.

Suggestion To thank Quote Answer

Share this page:

Share this page on...

SiePortal

Set-Point for I/O´s Sinamics G120

Created by: Urantia at: 12/6/2012 12:40 AM (5 Replies)

Rating (0)

Thanks 0

6 Entries

Urantia

Attachment

Graeme

Urantia

Attachment

Urantia

Attachment

Graeme

Attachment

Urantia

6 Entries

Related topics by keywords:

Follow us on

SiePortal

Set-Point for I/O´s Sinamics G120

Created by: Urantia at: 12/6/2012 12:40 AM (5 Replies)

Rating (0) Thanks 0

6 Entries

Urantia

Attachment

Graeme

Urantia

Attachment

Urantia

Attachment

Graeme

Attachment

Urantia

6 Entries

Related topics by keywords:

Follow us on

Rating (0)

Thanks 0