Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

SYSTEM FAULT with PLCSIM

Created by: iv73nikolov at: 6/14/2007 11:34 AM (7 Replies)

Rating (1)

Thanks 1

8 Entries

6/14/2007 11:34 AM	Rate (0)
iv73nikolov Posts: 41 Rating: (0)	Hi, experts ! After downloading the configuration of my S7-300 station to PLCSIM the simulator indicates SF and goes in stop mode. It says "Two order numbers found 6ES7 315-2AG10-0AB0 (of the inserted CPU) and 6ES 7841-0CC04-0YE0 of the firmware. Please give me an advice how to correct the problem and run simulations ... Attachment screenshot.JPG (630 Downloads)
iv73nikolov Posts: 41 Rating: (0)	Last edited by: iv73nikolov at: 14.06.2007 17:29 Last edited by: iv73nikolov at: 14.06.2007 11:34
Suggestion To thank Quote Answer

6/14/2007 6:38 PM	Rate (1)
Late Platinum Member Joined: 1/7/2006 Last visit: 5/11/2025 Posts: 2705 Rating: (321)	Hi, Thats normal, the stop is from something else, please save the diagnostic buffer and place that on the forum.
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users MonikerNameless

6/14/2007 7:29 PM	Rate (0)
iv73nikolov Posts: 41 Rating: (0)	Ok, I'll post the diagnostic buffer tomorrow. Now I'm at home, far away from siemens "that's normal" Thank you, Late !
iv73nikolov Posts: 41 Rating: (0)
Suggestion To thank Quote Answer

6/15/2007 8:25 AM	Rate (0)
iv73nikolov Posts: 41 Rating: (0)	Hi , Late ! I'm abslolutely new to PLCs and I'm not sure if this is the thing you need - see the attached file of the diagnostic buffer.. Attachment DIAGNOSE.pdf (705 Downloads)
iv73nikolov Posts: 41 Rating: (0)
Suggestion To thank Quote Answer

6/16/2007 3:35 PM	Rate (0)
Late Platinum Member Joined: 1/7/2006 Last visit: 5/11/2025 Posts: 2705 Rating: (321)	Hi, That is what I asking for, perfect, you are a fast learner. Event 2 of 15: Event ID 16# 530D New startup information in STOP mode Startup prevented by: - Parameter assignment for MPI or DP interfaces not evaluated or inconsistent (SDB1XXX incomplete, superfluous, or incorrect) - Module or submodule assignment not evaluated or evaluation aborted with errors (SDB1,3,5,2X,9X) There is a error in the Hardware configuration, especially with the MPI or DP communication. Please check what is programmed in the hardware, when you didn't find any errors then delete the suitecase in the blockcontainer and compile the hardware new. After that load the Hardware new inPLCSIM and try again. Have you made some connections in Netpro ? When you are not coming any further then check if your STEP7 is up-to-date and when not update it then to the newest in your version V5.3 (I believe SP3 is the newest). If that is also not helps then please place the project on the Forum, please consider that I have S7 V5.4 SP2 HF1
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

6/16/2007 7:15 PM	Rate (0)
iv73nikolov Posts: 41 Rating: (0)	I work on V5.4 too. After installation I downloaded new firmware updates and installed them. May be this causes the problem...But now is the weekend and don't think about work. In monday I will make the steps you proposed and now...have a nice weekend and thank you for your time spent for me!
iv73nikolov Posts: 41 Rating: (0)
Suggestion To thank Quote Answer

6/17/2007 12:50 PM	Rate (0)
Late Platinum Member Joined: 1/7/2006 Last visit: 5/11/2025 Posts: 2705 Rating: (321)	iv73nikolov I work on V5.4 too. After installation I downloaded new firmware updates and installed them. May be this causes the problem.Monday I will make the steps you proposed and now...have a nice weekend and thank you for your time spent for me! Hi, No thanks, please rate me when you have something about my answers and help... Have you STEP7 V5.4 without servicepacks... If yes, then please update to SP2... Normally I have only in the weekend some time to answer questions on the forum, so don't worry when I am not answering true the week.. Which version of PLCSIM do you have ?
	I hope that the answer will help, if you have still questions, don't hesitate to ask me. All the best, Late Never say never, think in solutions, not in trouble......
Suggestion To thank Quote Answer

6/18/2007 9:50 PM	Rate (0)
iv73nikolov Posts: 41 Rating: (0)	My PLCSIM is V5.3 + SP1 and STEP7 is V5.4 Prof + SP1...
iv73nikolov Posts: 41 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on