SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

type 1 & type 2

Created by: kinjalpatel1899 at: 7/2/2013 5:57 PM (4 Replies)

Rating (2)

Thanks 3

5 Entries

7/2/2013 5:57 PM	Rate (1)
kinjalpatel1899 Posts: 61 Rating: (15)	hi can anyone explain the difference between type 1 & type 2 co-ordination chart?
kinjalpatel1899 Posts: 61 Rating: (15)
Suggestion To thank Quote Answer

7/2/2013 6:11 PM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Please find here the details of coordination.
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users SMHZ jeet2907

7/5/2013 8:51 AM	Rate (0)
PISCEAN 2010 Posts: 8092 Rating: (884)	Please see the attached file for more information. Attachment 1 and type 2 coordination.pdf (600 Downloads)
PISCEAN 2010 Posts: 8092 Rating: (884)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users kinjalpatel1899

7/13/2013 7:40 AM	Rate (1)
@nkur Posts: 202 Rating: (16)	Hi there According to type1-the contactor contacts gets welded during the short ckt condition depending on the fault level,also that perticular switchgear becomes useless. In type2-the contactor contacts withstands the prescribed fault level and it again can be reused.
@nkur Posts: 202 Rating: (16)
Suggestion To thank Quote Answer

6/2/2014 2:10 PM
ashishmistry390 Posts: 21 Rating: (0)	kinjalpatel1899 hi can anyone explain the difference between type 1 & type 2 co-ordination chart? Dear Sir, Type ``2`` Requires that, under short-circuit conditions, the contactor or starter shall cause no danger to persons or installation and shall be suitable for further use. The risk of contact welding is recognized, in which case the manufacturer shall indicate the measures to be taken as regards the maintenance of the equipment. (No damage is allowed to either the contactor or overload relay. Light contact welding is permitted, but contacts must be easily seperable. No damage protection typically can only be provided by a currentlimiting device.) Type ``2`` Coordination (No-Damage Protection) for IEC and NEMA devices assures that the motor starter will be operable after a fault occurs and the fault corrected. Type ``2`` Coordination (No-Damage Protection) cannot prevent the initial fault from occurring. However, it assures all other components in the motor starter remain functional. To obtain Type ``2`` Coordination (No-Damage Protection) with either IEC or NEMA devices, motor starter manufacturers evaluate and test each combination of contactor, overload relay, and short-circuit protective device. The tests are as follows: A discrete low level fault test is performed at rated voltage. A high level short circuit withstand test, such as 100,000 amps, at rated voltage, is performed to check for the integrity of the contactor and overload relay. An overload relay and calibration test verifies operating characteristics and reliability. This test is performed before and after the low and high-level fault tests to determine if the overload relays sustained any damage during the test. Dielectric tests are performed to prove insulation adequacy after the low and high-level fault current tests have been completed. Regards, Ashish Mistry
ashishmistry390 Posts: 21 Rating: (0)
Suggestion Quote Answer

Share this page:

Share this page on...

SiePortal

type 1 & type 2

Created by: kinjalpatel1899 at: 7/2/2013 5:57 PM (4 Replies)

Rating (2) Thanks 3

5 Entries

kinjalpatel1899

PISCEAN 2010

This contribution was helpful to

PISCEAN 2010

Attachment

This contribution was helpful to

@nkur

ashishmistry390

5 Entries

Follow us on

Rating (2)

Thanks 3