Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

Logo basis don't RUN

Created by: daveDS at: 11/27/2020 9:13 AM (5 Replies)

Rating (0)

Thanks 0

6 Entries

11/27/2020 9:13 AM	Rate (0)
daveDS Posts: 3 Rating: (0)	The Logo basis 24RCo (6ED-1052-2HB00-0BA6) after running of years, went to the STOP modus, Is there a way to reset this, i allready turn the power off and on again, but only the extra module go in RUN mudus. If the module must be replaced, wich one do i need, because this module is end of life in 2018. hope someone can help me out thanks
daveDS Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

11/27/2020 9:20 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 1/16/2026 Posts: 36460 Rating: (4550)	The current replacement type would be 6ED1052-2HB08-0BA1. To use it, you need the current software version LSC V8.3. You could update this for free if you have an older full version. But you can no longer use the expansion modules of the 0BA6 with the current LOGO! S, you would have to buy them again.

Suggestion To thank Quote Answer

11/27/2020 10:17 AM	Rate (0)
daveDS Posts: 3 Rating: (0)	the modules aren't programmed, just simply used for turning lights on and off with push buttoms, so there is no option to repair are reset this modules? the setup is one power module with one RCo with extension (for all the lights and screens downstairs) and another RCo with extension for all the lights upstairs, and it's this one that stays red the extension is green but didn't work offcourse. so at the moment no lights upstairs :-(
daveDS Posts: 3 Rating: (0)	Last edited by: daveDS at: 11/27/2020 10:18:27
Suggestion To thank Quote Answer

11/27/2020 10:17 AM	Rate (0)
Scorp Platinum Member Joined: 2/22/2008 Last visit: 4/25/2025 Posts: 2698 Rating: (210)	The diagnostic of a Logo without display is not easy. The only way is Logosoft Comfort and a programming cable for this Logo. Then you can see the status or upload a backup of your program. If you need the exactly same module, then search on google or ebay. This module is also available from Siemens as spare part, but for a higher price than the new Logo8.2 or Logo8.3. Regards, Scorp

Suggestion To thank Quote Answer

11/27/2020 10:28 AM	Rate (0)
ixo65 Grandmaster Joined: 12/18/2014 Last visit: 1/16/2026 Posts: 36460 Rating: (4550)	daveDS The Logo basis 24RCo (6ED-1052-2HB00-0BA6) after running of years, went to the STOP modus, Is there a way to reset this, i allready turn the power off and on again, but only the extra module go in RUN mudus. If the LOGO! is in STOP, then is ist not enough to switch off power and then switch power on again. Connect the LOGO! with the LSC software and try there to start the program.
	Last edited by: ixo65 at: 11/27/2020 10:29:31
Suggestion To thank Quote Answer

12/10/2020 11:50 PM	Rate (0)
daveDS Posts: 3 Rating: (0)	Solved! Just set to Run byy program doesn't work. I create a new program upload this to the logo and it's working now. Thanks for supporting.
daveDS Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

Follow us on