Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

To publish the DBs of an IP262 card with STEP5, is it so tedious how I believe?

Created by: jm1983 at: 9/16/2011 5:12 PM (4 Replies)

Rating (0)

Thanks 0

5 Entries

9/16/2011 5:12 PM	Rate (0)
jm1983 Bronze Member Joined: 12/14/2010 Last visit: 6/28/2023 Posts: 160 Rating: (6)	Greetings for all, I am beginner programming with the STEP5 and I need you to clarify me a doubt. I only need to modify some DWs of the DBs (DB15, DB16, etc) of an IP262 card, but as I see the editor of the STEP5 forces us to enter all the values of the DWs of a certain DB beginning with the DW0. Is that this way? If for example, of the DB15 I do only need to modify DW12, DW13, DW14 and DW15, do I have to enter obligatorily also the values of the DW0 until the DW11? Thanks in advanced.

Suggestion To thank Quote Answer

9/19/2011 11:44 AM	Rate (0)
LXG Posts: 33 Rating: (0)	Hi, Write DW variables in the FORCE VARIABLES table in KH or KF format. Don't forget to insert DB nr. before variables. After that you can modify selected variables. Regards, LXG Attachment var.jpg (149 Downloads)
LXG Posts: 33 Rating: (0)
Suggestion To thank Quote Answer

9/19/2011 6:36 PM	Rate (0)
jm1983 Bronze Member Joined: 12/14/2010 Last visit: 6/28/2023 Posts: 160 Rating: (6)	Hello LXG, Thank you to respond. I proved what you suggested me but it has not worked me. I carried out the following steps: 1- Test-> Force Variables 2- In the chart that appears empty, i published the DWs of the DB15 that I want to change. 3- F6 (Activate), Appear ......... DB15 ......... DW12 KH = 0000 ......... DW13 KH = 0000 ......... DW14 KH = 0000 ......... DW15 KH = 0000 AS511 direct connection Status processing active 4- ESC, appears the possibility of forcing the process image, I enter to the DWs the wanted values, but, when concluding the edition of all the values I give ENTER but any message appear like the one that tells the manual "to Force finished". only the following thing: Operand: Force image process : ......... DB 15 ......... DW 12 KH = 0001 X ......... DW 13 KH = 0001 X ......... DW 14 KH = 0001 X ......... DW 15 KH = 0001 X AS511 direct connection What do you say?

Suggestion To thank Quote Answer

9/19/2011 8:44 PM	Rate (0)
jm1983 Bronze Member Joined: 12/14/2010 Last visit: 6/28/2023 Posts: 160 Rating: (6)	Hi again, I had not thought of a form very easy and obvious of achieving what I want. To transfer the DB15 from the IP262 card to the PC, to publish the DWs that is wanted and transfer it to the IP262 again.

Suggestion To thank Quote Answer

9/21/2011 7:50 AM	Rate (0)
LXG Posts: 33 Rating: (0)	Hello, According to your reply you change DW values from KH = 0000 to KH = 0001. I thing it works. Regards LXG
LXG Posts: 33 Rating: (0)	Last edited by: LXG at: 9/27/2011 9:15 AM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on