Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

SIMOTION SCOUT TIA: need to define the Drives in Integrerted SINAMIC

Created by: Inv0ker at: 1/9/2020 7:20 AM (4 Replies)

Rating (0)

Thanks 0

5 Entries

1/8/2020 7:20 AM	Rate (0)
Inv0ker Posts: 137 Rating: (1)	Hello EveryOne, i want to insure my Information [snip] ========================================================================== 5- ( SIMOTION SCOUT TIA ) ... i need to define the Drives in my Integrerted SINAMIC before i start to write the Program and then i define the AXES with Program ?? here i need some explaintion.. ========================================================================== in Advance... ------------------------------------------------------------------------------------------ Split from General Questions ! .
Inv0ker Posts: 137 Rating: (1)	Last edited by: Jen_Moderator at: 01/13/2020 06:25:28 New subject after splitting Last edited by: Jen_Moderator at: 01/13/2020 06:25:50 Division of questions into seperate topics.
Suggestion To thank Quote Answer

1/8/2020 7:33 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 11/5/2024 Posts: 22431 Rating: (3029)	Hi, [snip] 5.)what explanation exactly? Create the Simotion in TIA Open Simotion Configuration (Scout TIA) from TIA Portal Here you see the PLC ande the integrated Drive Configure the drive with the components you have and want to use. Regards Christoph
	Last edited by: Jen_Moderator at: 01/13/2020 06:28:10 Division of answers into seperate topics.
Suggestion To thank Quote Answer

1/9/2020 8:13 AM	Rate (0)
Inv0ker Posts: 137 Rating: (1)	ChristophD Hi, 1.) not in general. RS485 is the technical standard but not the protocol. RS485 can be Profibus protocol or for example Modbus-RTU- protocol. Simotion PLC and SIMATIC PLC support on the RS 485 Interface the PROFIBUS DP protocol and sometimes MPI Protocol, for the KLN please check the technical specification of the KLN. 2.) The SIMOTION D have a Integrated Sinamics S120 drive logic, no external S120 Device like CU320-2 is need 3.)DP = Decentral peripherie, generally speaking is DP= Profibus and PN = Profinet, this is right. 3b.) PROFINET is a special protocol/Technichs for Datatransfer over Ethernet basic (RJ45) 4.)DQ-Cables are Chrossover Cables with special shileding and wit additional 24v Powelines(depends which cable exactly) 5.)what explanation exactly? Create the Simotion in TIA Open Simotion Configuration (Scout TIA) from TIA Portal Here you see the PLC ande the integrated Drive Configure the drive with the components you have and want to use. Regards Christoph very much Christoph, [snip] about 5 ) i mean after i create my program and i insert the hardware in TIA then i open SIMOTION SCOUT TIA and i define the Drives then i mean next step : wright the Programm or i need to define the Axes first ? or together ... in Advance..
Inv0ker Posts: 137 Rating: (1)	Last edited by: Jen_Moderator at: 01/13/2020 06:35:15 Division of questions into separate topics.
Suggestion To thank Quote Answer

1/9/2020 8:35 AM	Rate (0)
jacek d Platinum Member Joined: 9/23/2005 Last visit: 11/5/2024 Posts: 4779 Rating: (728)	[snip] Ad. 5 To use motion/technology commands you need axes (TOs). Those axes can be virtual i.e. without drive connected. Connection to drives can be done later on.
	Last edited by: Jen_Moderator at: 01/13/2020 06:35:46 Division of questions into separate topics. Regards, Jacek What is confusing you is the fact that you never see a number but always its digit representation. So you end up thinking that the number is the representation. - Andrej Bauer Any claims against me - based on whatever legal reason - resulting from the use of any code and/or ideas presented on this forum shall be excluded. #StayWithUkraine
Suggestion To thank Quote Answer

1/13/2020 6:23 AM	Rate (0)
Jen_Moderator Diamond Member Joined: 6/19/2017 Last visit: 9/6/2024 Posts: 8175 Rating: (172)	New question published by Inv0ker is split to a separate thread with the subject Is there any differences formal between cables Ethernet and Drive-CliQ (SIMOTION)?. Best regards Jen_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on