Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

802d sl pro network connection

Created by: A.Pasandi at: 11/7/2012 8:06 PM (4 Replies)

Rating (0)

Thanks 0

5 Entries

11/7/2012 8:06 PM	Rate (0)
A.Pasandi Experienced Member Joined: 12/22/2010 Last visit: 11/23/2023 Posts: 95 Rating: (0)	Dear all, I want by plc and starter software by ethernet (X5 ethernet connection), sorry I can not connect by plc and starter software. I connect only by RCS802 software, (peer to peer connect) mode. How i can connect plc& starter software by ethernet connection? I read document opeation instructions,SECTION 9 in . Sorry I can not connect by this recipein catalog. best regards

Suggestion To thank Quote Answer

11/8/2012 4:57 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	A.Pasandi Dear all, I want by plc and starter software by ethernet (X5 ethernet connection), sorry I can not connect by plc and starter software. I connect only by RCS802 software, (peer to peer connect) mode. How i can connect plc& starter software by ethernet connection? I read document opeation instructions,SECTION 9 in . Sorry I can not connect by this recipein catalog. best regards Hello, What is the System software version are you using ?? What is the settings are you keeping first of all ? When you want to connect PLC tool...you need to make Set PG/PC interface selection..the access point should be Progamming tool 802-> TCP/IP->NdisWanlp here you need provide the IP address of 802D i.e 169.254.11.22 When you want to connect starter tool...you need to make the Set PG/PC interface selection ....the access point should be S7online(Setp 7)--> TCP/IP->NdisWanlp provide the IP address of 802D i.e 169.254.11.22 If you ensure this settings PLC pgming tool and starter is going to connect. Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

11/8/2012 7:11 AM	Rate (0)
A.Pasandi Experienced Member Joined: 12/22/2010 Last visit: 11/23/2023 Posts: 95 Rating: (0)	Hello, My sytem software is:V 01.04.01.07 802D sl T/M pro I go to system control: Shift+alarm-plc- connect off- modem on service display-service control fire service network-service firewall-select port no,102 and setting programming tool plc: I send for you by attached file When select double clik for refresh, after 10 sec, show missed: UNKNOWN Thank you Attachment Setting.pdf (238 Downloads)
	Last edited by: A.Pasandi at: 11/8/2012 7:14 AM
Suggestion To thank Quote Answer

11/8/2012 10:46 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	A.Pasandi Hello, My sytem software is:V 01.04.01.07 802D sl T/M pro I go to system control: Shift+alarm-plc- connect off- modem on service display-service control fire service network-service firewall-select port no,102 and setting programming tool plc: I send for you by attached file When select double clik for refresh, after 10 sec, show missed: UNKNOWN Thank you Hello, Could you try changing the access point i.e Progamming tool 802-> TCP/IP->NdisWanlp and check Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

11/8/2012 11:06 AM	Rate (0)
A.Pasandi Experienced Member Joined: 12/22/2010 Last visit: 11/23/2023 Posts: 95 Rating: (0)	Dear Prakash, RCS802 software connect by port no,80 for plc connect need release port no,102? you confirm for release port no.102: I go to service display-service control-service network-Service firewall and select and select port no.102 and push accept item.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on