Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

802D Tool wear offset value.

Created by: PISCEAN 2010 at: 2/12/2011 6:09 AM (7 Replies)

Rating (0)

Thanks 1

8 Entries

2/12/2011 6:09 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/30/2023 Posts: 8058 Rating: (856)	Hello experts, On one of our lathe machine with 802D controller, in the event of change in tool wear offset value, controller doesn't accepts the value more than 9. If the operter enter 10 or more than 10 controller doesn't accepts it. But if it is eneterd as 9 or less than 9 it works. But in the shop on other lathe machine with 802D controller, they even accepts the value as 30 also. What could be the problem? Is it related with any specific parameter value? if so please guide me Thanks in advance. DEEP.

Suggestion To thank Quote Answer

2/12/2011 8:08 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello Deep.... Check the parameter in Display MD 374 ? Regards, Ekalavya
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

2/12/2011 10:08 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/30/2023 Posts: 8058 Rating: (856)	Hello Ekalavya, thanks for your reply. I shall check & revert back to you. DEEP.

Suggestion To thank Quote Answer

2/12/2011 10:50 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hi Deep.... Value in 374 you can go up to=>9.9999 only.... Value 30 is not possible in this parameter!!!!! Regards, Ekalavya
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

2/12/2011 10:55 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/30/2023 Posts: 8058 Rating: (856)	Ekalavya Hi Deep.... Value in 374 you can go up to=>9.9999 only.... Value 30 is not possible in this parameter!!!!! Regards, Ekalavya Hi Ekalavya, I checked with other machine with same 802D controller, display MD value found 30. Surprise!!!!!. How you say it isn't possible. Regards, DEEP.

Suggestion To thank Quote Answer

2/12/2011 11:00 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hi Ekalavya, I checked with other machine with same 802D controller, display MD value found 30. Surprise!!!!!. How you say it isn't possible. Regards, DEEP. Hi... I checked in document thats why...... Regards, Ekalavya Attachment 802D_IBN.pdf (68 Downloads)
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

2/12/2011 11:10 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/30/2023 Posts: 8058 Rating: (856)	Ekalavya Hi Ekalavya, I checked with other machine with same 802D controller, display MD value found 30. Surprise!!!!!. How you say it isn't possible. Regards, DEEP. Hi... I checked in document thats why...... Regards, Ekalavya Hi, but I have checked & confirmed on 2 separate machines with 802 D controller present in shop, on 1 machine it is as 30 & on another machine it is as 15. Then how it can be set? Regards, DEEP.

Suggestion To thank Quote Answer

2/16/2011 8:14 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello DEEP.... Your right.... Values are getting changed 802D as well as in 802DSL noramlly it shouldn't be.... Regards, Ekalavya
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PISCEAN 2010

|

Share this page:

Share this page on...

Follow us on