Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

810D

Created by: Sanat21sp at: 2/27/2012 12:36 PM (10 Replies)

Rating (1)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

2/27/2012 12:36 PM	Rate (0)
Sanat21sp Posts: 15 Rating: (0)	Please share 810d commissioing manual. Also i have old DC spindle motor in CNC machine. I am using 6RA70 Dc drive. Is it possible to use it with profibus on 810D System or Using MPI Interface. Please suggest solution.
Sanat21sp Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/1/2012 7:37 AM	Rate (1)
Ekalavya Posts: 2964 Rating: (476)	Hello.... Attached information’s is of 810D commissioning....you can refere Docon CD/ Docon Web for more infromations....refer 810D/840D Startup guide. 810D works with MPI and the baudrate of 187.5kps Profibus is used for connecting profibus modules like PP module ET200 etc Regards, Prakash Attachment 810 D Commissioning.pdf (223 Downloads)
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

3/1/2012 6:37 PM	Rate (0)
Sanat21sp Posts: 15 Rating: (0)	Thank you very much...... After start up i am facing alarm 2001... PLC not started up.... Plz suggest solution... Is it because PLC doesnt contain any program or Drives are not configured
Sanat21sp Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/2/2012 6:50 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello.... The above said informations says there is no PLC program in CCU card.... Have you loaded your PLC project and checked???? Clear your PLC before doing any loading... Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

3/2/2012 11:44 AM	Rate (0)
Sanat21sp Posts: 15 Rating: (0)	Hello sir, I reset NCK and PLC before start up. Then before programming i uploaded deafault hardware configuration then it showed question mark. I have attached file. When i tried to replace object with similar one it shows firmware differences and PLC goes into stop mode. Attachment error.JPG (141 Downloads)
Sanat21sp Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/2/2012 1:32 PM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello.... Looks like there is no Sinumerik tool box installed in your PC....in your Hardware catlog you will be able to see this information open your S7300> in this there will be Sinumerik folder from here you need to physically configure the PLC CPU..... Check it out.... Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

3/5/2012 5:57 AM	Rate (0)
Sanat21sp Posts: 15 Rating: (0)	Hello Sir, Thank you. I changed hardware and selected perticular PLC module from Sinumerik Catlog. When i downloaded hardware it was running ok. Then i transferred basic program blocks. Actually i transferred all the blocks then it is showing error again. Abort error displayed on screen and PF and PS both loghts glows.
Sanat21sp Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/5/2012 6:07 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello.... In your simatic step7 goto PLC > Diagnostic > open Module Informations> open Diagnostic / Buffer....here you can see the error message... Check this... Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)
Suggestion To thank Quote Answer

3/19/2012 12:34 PM	Rate (0)
Sanat21sp Posts: 15 Rating: (0)	Dear Sir, I Have started machien successfully. Two axis motors are configured now. Now i want to configure DC Drive which is SimoReg 6RA70 Drive. I want to configure it on profibus. Is it possible to take spindle on profibus? Plz help.
Sanat21sp Posts: 15 Rating: (0)
Suggestion To thank Quote Answer

3/19/2012 1:31 PM	Rate (0)
Ekalavya Posts: 2964 Rating: (476)	Hello.... Check this link may be useful.... /tf/WW/en/Posts/49825 /tf/WW/en/Posts/49630 Regards, Prakash
Ekalavya Posts: 2964 Rating: (476)	Last edited by: Ekalavya at: 3/19/2012 1:37 PM one more link added
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on