Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

840D controller modifying program?

Created by: JoeMoran_Brettings at: 7/9/2012 5:42 PM (10 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

7/9/2012 5:42 PM	Rate (0)
JoeMoran_Brettings Posts: 38 Rating: (0)	We have an 840D Powerline controller and its doing some guffy things to program. Its adding random characters to programs. What do you think could be going on? Attachment 840Drandom.jpg (232 Downloads)
JoeMoran_Brettings Posts: 38 Rating: (0)
Suggestion To thank Quote Answer

7/9/2012 7:27 PM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi It seems that you have a virus. Try to install an antivirus. Good luck Nit

Suggestion To thank Quote Answer

7/10/2012 6:18 AM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 11/23/2024 Posts: 8092 Rating: (882)	JoeMoran_Brettings We have an 840D Powerline controller and its doing some guffy things to program. Its adding random characters to programs. What do you think could be going on? Does the program runs correctly? Means is it only display problem or when try to run the program, any error or message gets displayed?

Suggestion To thank Quote Answer

7/11/2012 5:50 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (484)	Hello... Have you tried running any other programs and checked are you getting the same characters in between the program. Could you check it out and revert back.... Regards, Prakash
Ekalavya Posts: 2964 Rating: (484)
Suggestion To thank Quote Answer

7/11/2012 11:28 PM	Rate (0)
JoeMoran_Brettings Posts: 38 Rating: (0)	The program will not run once it hits the bad lines of code. Gives an error message unable to read... Other programs run fine. Cant explain it but now the program works fine after deleting it and reloading the program a few times its stable. Was able to run it. When we outputed the "bad" code it was also corrupted. the screen shot i have in the first post is an outputed program. Oh well dont know why. thx
JoeMoran_Brettings Posts: 38 Rating: (0)
Suggestion To thank Quote Answer

7/12/2012 8:50 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi If other programs are Ok, maybe you have a virus on the computer on which you've generated the program. I've encountered same issues on other types of controller to. Good luck Nit

Suggestion To thank Quote Answer

7/15/2012 12:08 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Hi NCK damage (RAM ) ? (Was the Programm loaded in NCK, or only in the PCU/MMC ?) Harddisk damage ? Virus ? Regards Karl
	Karl
Suggestion To thank Quote Answer

7/17/2012 4:32 PM	Rate (0)
JoeMoran_Brettings Posts: 38 Rating: (0)	Had it happen again. It only happens when the operator modifies the program to change a value. For example a feed rate. When they then save it, it will corrupt. This is not all the time but some times.
JoeMoran_Brettings Posts: 38 Rating: (0)
Suggestion To thank Quote Answer

7/19/2012 10:20 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi Try to delete all the programs from NC directory, power off and power on and see if it is hapen again. I've encountered similar issue but for tools. Good luck Nit

Suggestion To thank Quote Answer

7/20/2012 11:08 PM	Rate (0)
JoeMoran_Brettings Posts: 38 Rating: (0)	I think i might have the answer to this. What we ended up doing was clearing the NC and PLC with the rotary switch in the cabinet and then reloading the NC archine. So far now issues in little over a day.
JoeMoran_Brettings Posts: 38 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on