Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

about 6ES7 138-4DA04-0AB0 counter modul

Created by: freeman1907 at: 7/11/2012 10:14 AM (6 Replies)

Rating (0)

Thanks 1

7 Entries

7/11/2012 10:14 AM	Rate (0)
freeman1907 Posts: 28 Rating: (1)	Hi everybody.. I would like to use this modul but i couldnt find any sample of it.And i coldnt understand so much from its manuel.Is there any example how to use of it?? And in its manuel adress 5.0 says that LOAD_VAL, could anyone explain that what the meaning of it is??? With Best Regards
freeman1907 Posts: 28 Rating: (1)
Suggestion To thank Quote Answer

7/11/2012 11:39 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 9/14/2023 Posts: 8592 Rating: (1132)	freeman1907 ....And in its manuel adress 5.0 says that LOAD_VAL, could anyone explain that what the meaning of it is??? Hello, With this bit, you can give the counter direct a "Start" value. (Start value is in byte 0 to byte 3) Best regards, Wizard

Suggestion To thank Quote Answer

7/11/2012 11:48 AM	Rate (0)
freeman1907 Posts: 28 Rating: (1)	Hii Thanks for reply.So if i do this and set 5.0, it starts from 1000...ıs ıt true or false?? L 1000 T "LP_Encoder".OFFSET T DB124.DBD 4 SET S "LP_Encoder".SW_GATE With Best Regards
freeman1907 Posts: 28 Rating: (1)
Suggestion To thank Quote Answer

7/11/2012 12:00 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 9/14/2023 Posts: 8592 Rating: (1132)	freeman1907 Hii Thanks for reply.So if i do this and set 5.0, it starts from 1000...ıs ıt true or false?? L 1000 T "LP_Encoder".OFFSET T DB124.DBD 4 SET S "LP_Encoder".SW_GATE With Best Regards Hello freeman1907, I'm a bit confused Let's try to help: You want to start from 1000. L 1000 T DB1.DBD 0 (You have to copy this DB1.DBD 0 to the right output bytes) Set DB1.DBX 4.0 (To open SW Gate) Set DB1.DBX 5.0 (Load Val) A DB2.DBX 4.0 (load function running, this is an input from module) Reset DB1.DBX 5.0 Hope this will help Best regards, Wizard

Suggestion To thank Quote Answer

7/11/2012 2:43 PM	Rate (0)
freeman1907 Posts: 28 Rating: (1)	Hii I made a program with the help of your cods.So could you please look at this that is there anything wrong??It starts from 0..At the attachment file.... With Best Regards Attachment plcp.pdf (399 Downloads)
freeman1907 Posts: 28 Rating: (1)
Suggestion To thank Quote Answer

7/11/2012 3:19 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 9/14/2023 Posts: 8592 Rating: (1132)	Hi, In network 1, you set offset to 0 and control bits to 0 except Software gate it is high (open) (I think this should be once not every time!!!!) Network 2 you want to load start value of counter. First you must give DB9.DBD0 a value (Example 1000) Then you must set DB9.dbx5.0 And when DB9.DBX12.0 is high, you can reset DB9.dbx5.0 Hope this will help. Best regards, Wizard
	Last edited by: Wizard at: 7/11/2012 3:19 PM
Suggestion To thank Quote Answer

7/11/2012 3:53 PM	Rate (0)
freeman1907 Posts: 28 Rating: (1)	Hiii Thank You Very Much for your Helps With Best Regards
freeman1907 Posts: 28 Rating: (1)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Wizard

|

Share this page:

Share this page on...

Follow us on