Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

BW500 Error

Created by: AutoGen_564002 at: 4/27/2015 8:40 AM (9 Replies)

Rating (0)

Thanks 2

10 Entries

4/27/2015 8:40 AM	Rate (0)
AutoGen_564002 Regular Member Joined: 3/13/2015 Last visit: 6/8/2022 Posts: 9 Rating: (0)	Dear all, I had an new Siemens belt scale system with 3 MSI, speed sensor WS300. Belt rate: 120 t/h design speed: 1.2 m/s BW500: 7MH7152-2AA00-2EA-Z Y77 The system working fine two day after installation before error. The problem as follow: When system is running, the display of BW500 fault, the speed, belt load, total is pause. (its remain value and not change for along time), and not working, some keypad still working ( Alt Disp, par,1,2..0, up, down). It only working again when i turn off and on power supply for the BW500. I don't know what's problem and how to resolve it. I had installation many Siemens belt scale system and never had problem. Anyone please help!

Suggestion To thank Quote Answer

4/27/2015 11:33 AM	Rate (0)
Levelmans Bronze Member Joined: 12/13/2012 Last visit: 1/16/2019 Posts: 124 Rating: (45)	Hello , sounds strange. Is there a error code displayed ? I guess, this could be a contact conflict of the speed sensor. If the WS300 is not working, the BW500 will not calculate anymore. Please check the cable of the WS 300, it could be that this is grazed from the belt etc. Hope this helps ! Cheers

Suggestion To thank Quote Answer

4/27/2015 12:09 PM	Rate (0)
AutoGen_564002 Regular Member Joined: 3/13/2015 Last visit: 6/8/2022 Posts: 9 Rating: (0)	Many Thank Levelmans, There is No error code. The wiring of the speed sensor is very carefully, but I will check it again. when error occur the Speed value =1.101 m/s (equal the last time value when it pause) ; the belt load =22.05 kg/m (equal the last time value when it pause) and total 1225.4 t/h (equal the last time value when it pause) and it's remain value while belt still running and material feeding, it's only working normally when turn off and on power supply . I thinks if speed sensor signal disconnected the speed value will go to 0 m/s and feed rate 0 t/h. Any other ideal please advice me.

Suggestion To thank Quote Answer

5/4/2015 5:46 AM	Rate (0)
AutoGen_564002 Regular Member Joined: 3/13/2015 Last visit: 6/8/2022 Posts: 9 Rating: (0)	Dear Mr Levelmans, I checked wiring, there is no conflict. Please see the link bellow for detail of the error: https://www.youtube.com/watch?v=6mL6gj1gQzw

Suggestion To thank Quote Answer

6/15/2015 5:13 PM	Rate (0)
Levelheaded Regular Member Joined: 6/13/2013 Last visit: 7/15/2022 Posts: 24 Rating: (2)	What is the serial number of the unit?

Suggestion To thank Quote Answer

7/31/2015 6:03 AM	Rate (0)
AutoGen_564002 Regular Member Joined: 3/13/2015 Last visit: 6/8/2022 Posts: 9 Rating: (0)	Hi TheBestWeigh, The Serial no: PBD/F2050447

Suggestion To thank Quote Answer

8/24/2015 4:27 PM	Rate (0)
Levelheaded Regular Member Joined: 6/13/2013 Last visit: 7/15/2022 Posts: 24 Rating: (2)	Thank you for the serial number, and sorry for the late reply. It looks as though this unit is in a range which is under a factory noted failure. Please contact the returned goods department for a full warranty covered unit. Sorry for the inconvenience.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users AutoGen_564002

8/28/2015 5:44 AM	Rate (0)
AutoGen_564002 Regular Member Joined: 3/13/2015 Last visit: 6/8/2022 Posts: 9 Rating: (0)	We have replace new BW500 from Siemens and it works fine now Many thanks for your help.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Min_Moderator

11/17/2015 2:34 PM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4792 Rating: (123)	New question published by ALI ALOBIDY is split to a separate thread with the subject Siemens milltronics BW500 belt weighing system, couldn't return to run menu. Best regards Min_Moderator

Suggestion To thank Quote Answer

1/10/2016 10:52 AM	Rate (0)
CS Moderator Moderator Joined: 9/1/2005 Last visit: 8/24/2023 Posts: 4102 Rating: (193)	New question published by KNOTA is split to a separate thread with the subject BW500 download error. Best regards CS Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards CS Moderator
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on