Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Calculator option in 840D

Created by: ŠΜS at: 9/1/2011 6:33 AM (4 Replies)

Rating (0)

Thanks 0

5 Entries

9/1/2011 6:33 AM	Rate (0)
ŠΜS Silver Member Joined: 6/7/2010 Last visit: 7/9/2024 Posts: 571 Rating: (37)	Hello… How tobring Calculator option in offset page in 840D, PCU50.
	Regards, ŠΜS
Suggestion To thank Quote Answer

9/1/2011 10:30 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Hi You must make changes in following: Regie.iNI . Test this: [TASKCONFIGURATION] Task16=name := OEMFRAME, cmdLine := "calc.exe", Timeout := 10000, PreLoad := False OEMFRAME.INI [CALC] X=300 Y=300 WIDTH=300 HEIGHT=300 AEDITOR.INI: [CHILDS] OEMFRAME=17 Softkey: AEDITOR.COM: HS16=("CALC") EXE(OEMFRAME) END_PRESS RE_RO.INI: You must put here your language [HSoftkeyTexts] HSK16="CALC" Good luck Nit

Suggestion To thank Quote Answer

9/1/2011 10:53 AM	Rate (0)
ŠΜS Silver Member Joined: 6/7/2010 Last visit: 7/9/2024 Posts: 571 Rating: (37)	Hi Nit , Yesterday i followed the Same steps, but i faced problem in finding the RE_RO.INI file, Regie.iNI . Test this: [TASKCONFIGURATION] Task16=name := OEMFRAME, cmdLine := "calc.exe", Timeout := 10000, PreLoad := False I have Change this in Regie.ini OEMFRAME.INI [CALC] X=300 Y=300 WIDTH=300 HEIGHT=300 I have Change this in OEMFRAME.ini AEDITOR.INI: [CHILDS] OEMFRAME=17 ( HERE i could not find OEMFRAME below [CHILDS]) Softkey: ( For this i need to add the below line in AEDITOR.COM?) AEDITOR.COM: HS16=("CALC") EXE(OEMFRAME) END_PRESS RE_RO.INI:( Cannot find this file ) You must put here your language [HSoftkeyTexts] HSK16="CALC"
	Regards, ŠΜS
Suggestion To thank Quote Answer

9/1/2011 7:46 PM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Muthamil_S Hi Nit , Yesterday i followed the Same steps, but i faced problem in finding the RE_RO.INI file, Regie.iNI . Test this: [TASKCONFIGURATION] Task16=name := OEMFRAME, cmdLine := "calc.exe", Timeout := 10000, PreLoad := False I have Change this in Regie.ini->OK OEMFRAME.INI [CALC] X=300 Y=300 WIDTH=300 HEIGHT=300 I have Change this in OEMFRAME.ini->OK AEDITOR.INI: [CHILDS] OEMFRAME=17 ( HERE i could not find OEMFRAME below [CHILDS])->You must add it Softkey: ( For this i need to add the below line in AEDITOR.COM?)->Yes AEDITOR.COM: HS16=("CALC") EXE(OEMFRAME) END_PRESS RE_RO.INI:( Cannot find this file ) You must find the ini file for your language instead of RO (i.e for English it must be RE_EN.INI or RE_GR.INI for German language) [HSoftkeyTexts] HSK16="CALC" Good luck Nit
	Last edited by: Nit at: 9/1/2011 7:49 PM
Suggestion To thank Quote Answer

9/1/2011 8:12 PM	Rate (0)
SteveA Posts: 297 Rating: (41)	There is a simple calculator available in almost all number entry fields on the PCU50. You just press the = key and the current value is copied to a line just above the field. You can add, subtract, multiply,divide, convert to metric (M) or convert to inch(I). Press enter when done to accept the calculated value. HTH, SteveA
SteveA Posts: 297 Rating: (41)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on