Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Can’t download into S7-1200 CPU1214C

Created by: Import-User-1 at: 6/10/2011 3:39 PM (9 Replies)

Rating (1)

Thanks 2

10 Entries

6/10/2011 3:39 PM	Rate (0)
Import-User-1 Posts: 3609 Rating: (29)	Guest Hi,We’ve recently manage to get a S7-1200 CPU 1214C for evaluation. Soon my enthusiasm turned into a loot of frustrations. In short, my problem is that I can’t download into the PLC. I can ping it. I can see it as available device, I can flash the LED's, I can change the IP. Here is what I’m doing:Start new projectAdd a new deviceChange the Profinet IP address of the device to 192.168.1.105The IP address was previously assigned from > Online access…… to 192.168.1.106The device replays when PING-edCompile allDownload allExtended download to device windows pops up> check Show all accessible devices.Myplc is detectedClick “Load” and the result is “Connection failed, the selected online target could not be reached”. The form caption is Assign IP address (0132:000002).I’ve tried the following drivers PG/PC, but non of them worked: ISO Ind. Ethernet -> Marvell Yukon Gigabit Diagnostic looks okTCP/IP -> Marvell Yukon Gigabit ...TCP/IP(Auto) -> Marvell Yukon Gigabit ... TCP/IP -> NdisWanIp <Active> Diagnostic Failed SR Test: access point using this parameter set: ->S7ONLINE Error in function call SRMD_Set(..) Error: No interface handle Version ID: DLL Version 8.1.2003.4124Many thanks,Cristian
Import-User-1 Posts: 3609 Rating: (29)
Suggestion To thank Quote Answer

6/10/2011 4:59 PM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 12/2/2024 Posts: 10229 Rating: (1181)	Hello, What version of TIA do you have and what is the OS there? Best regards, Hristo MIhalev

Suggestion To thank Quote Answer

6/10/2011 5:37 PM	Rate (1)
bakerjw Posts: 126 Rating: (18)	Can you go online with the old IP Address? If you can conect with it online then do a reset to factory defaults. What are the versions of the firmware and the TIA portal?
bakerjw Posts: 126 Rating: (18)
Suggestion To thank Quote Answer

6/10/2011 7:22 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/5/2024 Posts: 15466 Rating: (2453)	Did you power cycle the CPU/PLC? If not, try that first. What firmware revision is loaded on the PLC? If it is less than 1.0.2 please upgrade to at least 1.0.2. What operating system are you using? If it is windows 7, it must be 32-bit. If it is win xp, it should work. As to which to use, if you can communicate by pinging, and you can flash the LEDs, it should go online as long as the software version matches the PLC firmware version. PLCs with firmware 2.0 or higher will not communicate with V10.5 SP2 of the TIA Portal. Hope that helps.
	science guy
Suggestion To thank Quote Answer

6/10/2011 10:04 PM	Rate (0)
MrPaiva Silver Member Joined: 6/29/2010 Last visit: 10/27/2022 Posts: 112 Rating: (63)	The TIA10.5 SP2 can communicate with v2 firmware CPUsnormaly, only the functionality of the v2 firmware not able to be used.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tomy Master

6/13/2011 3:06 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/5/2024 Posts: 15466 Rating: (2453)	MrPaiva The TIA10.5 SP2 can communicate with v2 firmware CPUsnormaly, only the functionality of the v2 firmware not able to be used. My experience with loading V2 firmware differs. I loaded the firmware, and could ping the PLC, but I could not connect via TIA Portal 10.5 SP2. I loaded FW 1.0.2 and communicated just fine. Maybe the original poster is having a similar problem.
	science guy
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Jacques-Olivier

6/14/2011 3:20 PM	Rate (0)
bakerjw Posts: 126 Rating: (18)	If you cannot perform a factory reset of the PLC with the TIA Portal then try an empty MMC memory card. If clearing the PLC with a Simatic memory card, it should only have the following hidden or system files on it. __LOG__ crdinfo.bin You might also use the IPTool. I can dig dig up a link to it if needed. Once you get back top square one yuo should be fine.
bakerjw Posts: 126 Rating: (18)
Suggestion To thank Quote Answer

6/16/2011 1:34 PM	Rate (0)
MrPaiva Silver Member Joined: 6/29/2010 Last visit: 10/27/2022 Posts: 112 Rating: (63)	Only a tip, If the CPU with v2 firmware has a v11 program, maybe you cannot perform download to CPU with TIA 10.5 SP2, you have to do MRES, so you will communicate normaly with CPU by TIA 10.5 SP2.

Suggestion To thank Quote Answer

1/26/2014 10:34 PM	Rate (0)
CS Moderator Moderator Joined: 9/1/2005 Last visit: 12/5/2024 Posts: 4114 Rating: (195)	New question published by Kapetan is split to a seperate thread with the subject Connection Step 7 Profesional V11 to S7-1200 after instaling Simatic.NET 8.0 Best regard CS Moderator
	My Forum is the place to personalize your profile, track your topics, and maintain content that interests you. Best regards CS Moderator
Suggestion To thank Quote Answer

5/4/2016 11:45 AM	Rate (0)
Min_Moderator Platinum Member Joined: 9/3/2014 Last visit: 3/13/2019 Posts: 4766 Rating: (122)	New question published by industry support is split to a separate thread with the subject CPU 1212C, TIA V13, can not download program to PLC. Best regards Min_Moderator

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on