Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

can,t running 840D using G-code genarate by CATIA

Created by: najib at: 11/10/2007 6:08 PM (5 Replies)

Rating (0)

Thanks 0

6 Entries

11/10/2007 6:08 PM	Rate (0)
najib Posts: 1 Rating: (0)	hi guy.. somebody please help me.. my final project is fabricate car side mirror.. the problem is, whn i try running using sinumerik at pc (sinumerik pc suitable software).... the g code cannot be simulate, the srceen display "channel 1 selected program C:\ SI_TRAIN\DH\WKS.DIR\SHOPMILL not available or is e* " I also don’t know to transfer g-code to machine.. I connect the pc (same comp. name load-in in machine) by USB, but machine cannot load in. i tried since 2 month but still failed.. if you kindly.. you can try my G-code.. may be some thing wrong with my G-code ;====================================================== ;=== cPost Standard PP for SINUMERIK 840 D === ;====================================================== N10 G0 G90 G40 N20 G40 M8 N30 G17 N40 ;=============== TOOL CHANGE ================= N50 ; DESC : N60 ;============================================= N70 T1 M06 N80 D1 N90 G0 G90 G40 G17 N100 F0 S0 N110 G64 SOFT N120 G0 X234.204 Y-167.9 Z100.971 S70 M3 N130 G0 Z2.553 N140 G1 X240 Z1 F300 G94 N150 X0.01 F1000 N160 Y-164.9 N170 X239.99 N180 Y-161.9 N190 X0.01 N200 Y-158.9 N210 X239.99 N220 Y-155.9 N230 X0.01 N240 Y-152.9 N250 X239.99 N260 Y-149.9 N270 X0.01 N280 Y-146.9 N290 X239.99 N300 Y-143.9 N310 X0.01 N320 Y-140.9 N330 X239.99 N340 Y-137.9 N350 X0.01 N360 Y-134.9 N370 X239.99 N380 Y-131.9 N390 X0.01 N400 Y-128.9 N410 X239.358 N420 X239.99 Y-125.9 N430 X0.01 N440 Y-122.9 N450 X239.99 N460 Y-119.9 N470 X0.01 N480 Y-116.9 N490 X239.99 N500 Y-113.9 N510 X0.01 N520 Y-110.9 N530 X239.99 N540 X239.485 Y-107.9 N550 X0.01 N560 Y-104.9
najib Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

11/14/2007 2:36 PM	Rate (0)
denzilg_sa Bronze Member Joined: 7/5/2007 Last visit: 3/15/2023 Posts: 76 Rating: (5)	Hi najib It seems if the post has not been set up correctly, as this is generating unneccary G codes, G40 is modal this means that Cutter comp is disabled on power on or reset, normally G40 must also be programmed with one of the axis that was used for G41,G42 In your case I would remove all G40 as they are not needed. Also when down loading programs the USB must be activaited as would a stiffy drive with Drive A: I do not know if this is done, but you could use the RS232 port on the OP to upload or down load your programs, remember to set the interface signals. Hope this could help Regards Denzil
	Last edited by: denzilg_sa at: 14.11.2007 14:48
Suggestion To thank Quote Answer

11/15/2007 11:31 PM	Rate (0)
Pee Ell Sea Posts: 672 Rating: (56)	HI, Are you using Sinutrain ? Can you edit the program within the Sinutrain package ?
Pee Ell Sea Posts: 672 Rating: (56)
Suggestion To thank Quote Answer

6/10/2008 2:08 PM	Rate (0)
prasha Posts: 4 Rating: (0)	Dear najib I think you need to check your programe start lines, Please use any standered siemens part programe and refer programe start and end according. Hope it help you..... Here is the example..... %_N_pumpEndP_MPF ;$PATH=/_N_MPF_DIR ;MPF_pumpEndP Regards, Prashant Pawar.
prasha Posts: 4 Rating: (0)
Suggestion To thank Quote Answer

6/11/2008 8:27 PM	Rate (0)
Pee Ell Sea Posts: 672 Rating: (56)	Hi, Your problem is one of three. The message you get is telling you it cannot even try to run your program so it has n't got as far as checking G codea 1, The program does not exist in the correct sinutrain directory 2, The program is not enabled 3, The program is open in edit mode when you try to run it. 1, Can you see the program in the program edittor and is it in the program directory. Create a program in the program edit mode and if you can run it cut and paste your program into it. 2, Enable the program 3, Close the program edit mode before trying to run the program Hope it helps
Pee Ell Sea Posts: 672 Rating: (56)
Suggestion To thank Quote Answer

10/16/2008 6:00 PM	Rate (0)
Ianbig Posts: 2 Rating: (0)	Minor comment: I find I have to keep the M06 on a separate line for the program to work ! Ian
Ianbig Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on