Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Change parameter value by input high

Created by: ŠΜS at: 3/31/2011 6:11 PM (8 Replies)

Rating (0)

Thanks 2

9 Entries

3/31/2011 6:11 PM	Rate (0)
ŠΜS Silver Member Joined: 6/7/2010 Last visit: 7/9/2024 Posts: 571 Rating: (37)	Dear All, I need to change 30500 parameter from value 1 to 2 ,when one input gets high.Is it possible ? If yes How could we do? ( System is 840D)
	Regards, ŠΜS
Suggestion To thank Quote Answer

3/31/2011 8:41 PM	Rate (0)
Caldas Bronze Member Joined: 9/10/2007 Last visit: 2/10/2025 Posts: 71 Rating: (1)	You can use: IF $A_IN[1]==1 $MA_INDEX_AX_ASSIGN_POS_TAB[AX1]=2 ENDIF ... Good luck.
	Last edited by: Caldas at: 3/31/2011 8:42 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users ŠΜS

3/31/2011 8:51 PM	Rate (0)
Martinsrf Posts: 8 Rating: (0)	Caldas is right
Martinsrf Posts: 8 Rating: (0)
Suggestion To thank Quote Answer

4/1/2011 4:23 AM	Rate (0)
ŠΜS Silver Member Joined: 6/7/2010 Last visit: 7/9/2024 Posts: 571 Rating: (37)	Caldas You can use: IF $A_IN[1]==1 $MA_INDEX_AX_ASSIGN_POS_TAB[AX1]=2 ENDIF ... Good luck. Thanka Caldas,I which folder ineed to write this Command. Eg: F drive dh file or mmc file.........
	Regards, ŠΜS
Suggestion To thank Quote Answer

4/1/2011 7:31 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (484)	Hello.... If i understand you need to write it in your MPF/ SPF.... Regards, Ekalavya
Ekalavya Posts: 2964 Rating: (484)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users ŠΜS

4/1/2011 8:11 AM	Rate (0)
ŠΜS Silver Member Joined: 6/7/2010 Last visit: 7/9/2024 Posts: 571 Rating: (37)	Ekalavya Hello.... If i understand you need to write it in your MPF/ SPF.... Regards, Ekalavya Thanks Ekalavya,In my application I need tochangethat parameter value in jog mode.but if i save in progam.I need to trigger the program in MDA.so is there anycommand to trigger the program while input is high in jog mode?
	Regards, ŠΜS
Suggestion To thank Quote Answer

4/1/2011 8:39 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (484)	Hello.... Try assign an input on your MCP if you press that the particular programs runs.... Check this...may be helpful in your case.... Regards, Ekalavya
Ekalavya Posts: 2964 Rating: (484)
Suggestion To thank Quote Answer

4/1/2011 10:29 AM	Rate (0)
OvidiuNastac Silver Member Joined: 1/29/2008 Last visit: 7/26/2022 Posts: 419 Rating: (19)	Muthamizh Ekalavya Hello.... If i understand you need to write it in your MPF/ SPF.... Regards, Ekalavya Thanks Ekalavya,In my application I need tochangethat parameter value in jog mode.but if i save in progam.I need to trigger the program in MDA.so is there anycommand to trigger the program while input is high in jog mode? Hi I think you could use Asincronious Actions trigered by the imput. Good luck Nit

Suggestion To thank Quote Answer

4/6/2011 6:10 PM	Rate (0)
chinna Experienced Member Joined: 9/10/2007 Last visit: 2/6/2025 Posts: 78 Rating: (3)	Hai, As nit said you need to use the When do synchronized action ... it will help for you application... Can you please explain your application clearly. Regards, Chinna

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on