Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Configuration networks S7400-H and 8 S7300 ,connect via profinet

Created by: xuanbach1985bk at: 6/30/2009 6:51 AM (4 Replies)

Rating (0)

Thanks 5

5 Entries

6/30/2009 6:51 AM	Rate (0)
xuanbach1985bk Posts: 3 Rating: (0)	Hi All, i am a newbie, i have a system with S7400-H and 8 S7300, connect via profinet ,can you help me configure my system in STEP7 HW Config . Thank for all. Best Regards. Attachment image.JPG (310 Downloads)
xuanbach1985bk Posts: 3 Rating: (0)
Suggestion To thank Quote Answer

6/30/2009 7:43 AM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 1/14/2025 Posts: 10239 Rating: (1182)	Hello, I suggest you to start with What information is currently available on the topic of PROFINET? Basically there you'll find all necessary info. And later if you have questions let me know. Regards Hristo Mihalev

Suggestion To thank Quote Answer
This contribution was helpful to 3 thankful Users Enigma H-H xuanbach1985bk

6/30/2009 4:32 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello, I think Hristo is right, but please let me add two points. 1. PROFINET is not released for S7-400 H System at all, so you will not run PROFINET IO or CBA with it... at least as far as I know. 2. The only Ethernet communicationpossible here would be either the use of S7-Communication or the use of Send / Receive (T-Communication) between the S7-300 and the S7-400. This is both not being done in HW Config... Maybe you begin to read in the NCM S7 Manuals or in the manual for the Open Communication Wizard, depending which interface you use (CP or CPU). Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users xuanbach1985bk

6/30/2009 5:45 PM	Rate (0)
xuanbach1985bk Posts: 3 Rating: (0)	Thanks for all, I am not good at English to express my ideas . In my system I only use Wincc(OS) in PC to collect information form PLC and control them, no communication between the PLC, and I use lean manage switch made by phoenixcontact to comunicate (same with some Switch made by siemens ) and I don't know how to configure it by Step7. Please make it clearly for me , thanks so much....
xuanbach1985bk Posts: 3 Rating: (0)	Last edited by: xuanbach1985bk at: 6/30/2009 5:48 PM
Suggestion To thank Quote Answer

7/1/2009 2:50 PM	Rate (0)
J_Bell Posts: 5822 Rating: (412)	Hello, maybe you explain a bit more about yourWin CC system. What Protocol or Driver do you intent to use in this system? I wonder, how do you plan on handling the S7-H System seen from the communication point of view. Do you plan to use a redundant S7 Connection with S7-Redconnect or do you plan on doing another connection type I don't think of at the moment. Best regards J_Bell
J_Bell Posts: 5822 Rating: (412)	Last edited by: J_Bell at: 7/1/2009 2:55 PM Last edited by: J_Bell at: 7/1/2009 2:53 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users TMOJ

|

Share this page:

Share this page on...

Follow us on