SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

CP340-TO-PRİNTER

7/25/2011 8:38 AM	Rate (0)
samstrong Posts: 59 Rating: (0)	Hello. cp and 340 to the printer I want to send some process information. I need a sample program. format is. process name- date(dd-mm-yy)- time (hh-mm-ss)- process value example: room pt100 25.08.2011 09.37.55 25 (degree) thanks so much
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

7/25/2011 9:41 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 3/14/2025 Posts: 8894 Rating: (1185)	Dear samstrong, Have you seen this link: Sample program for the CP340; printer mode Best regards, Wizard

Suggestion To thank Quote Answer

7/25/2011 11:53 AM	Rate (0)
samstrong Posts: 59 Rating: (0)	hi. thanks for your interest. but it is STL. I dont understand this langauge. I know FBD and ladder. can you change for me please.
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

7/26/2011 8:46 AM	Rate (0)
samstrong Posts: 59 Rating: (0)	hi. it is very impotant for me. ı need a simple program. best regards
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

7/26/2011 10:08 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 3/14/2025 Posts: 8894 Rating: (1185)	Hello, Here is printout of FC1 (It is FC12 in FBD) Hope it will help. Best regards, Wizard Attachment fc1.pdf (102 Downloads)

Suggestion To thank Quote Answer

7/26/2011 11:27 AM	Rate (0)
samstrong Posts: 59 Rating: (0)	hi. tahnks so much. I trying now. see u
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

7/27/2011 3:26 PM	Rate (0)
samstrong Posts: 59 Rating: (0)	hi, I load to plc the program. but I did not run. I need a simple program . I have a bit m0.0. if m0.0 1, plc send a process valu in "date-name-value" format to printer. I m not successfull still yet. thanks
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

7/27/2011 3:38 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 3/14/2025 Posts: 10239 Rating: (1183)	<OFFTOPIC> I think after Wizard made the logic in LAD/FBD is a much easier for you to make an adaptation to the actual project. Take a look at M28.0 and M28.1. Each block there has a EN input.If you put there some condition, execution of the same will depends of the actual state of condition... Best regards, Hristo MIhalev

Suggestion To thank Quote Answer

7/27/2011 4:09 PM	Rate (0)
samstrong Posts: 59 Rating: (0)	Hello. so I enable it as a link if any bit is set and if I can receive output from the printer? also I can read a maximum of 2 characters. how to increase it? frankly do not understand what is being done in this program. I could not find it by any use in Turkey.I need a person could get more support. ie it is history-name-value by pressing any button I want to print it out. but I could not.This is a complicated situation for me.also I found a document on the site. I said something to this that I do not understand, but it also.This document is attached. best regards Attachment example_340.GIF (96 Downloads)
samstrong Posts: 59 Rating: (0)
Suggestion To thank Quote Answer

Share this page:

Share this page on...