Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

CU320 S120 Motor Parameter recording

Created by: vorapob at: 7/13/2018 4:07 AM (8 Replies)

Rating (2)

Thanks 0

9 Entries

7/13/2018 4:07 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	Dear Experts, I need help about SINAMICS S120 motor current recording. How can I record motor current from CU320-2 PN/DP ? I use S120 and CU320 as picture. Thank you. Best Regards, Vorapob Attachment Motor current.jpg (69 Downloads)
	Best Regards, Vorapob
Suggestion To thank Quote Answer

7/13/2018 8:31 AM	Rate (1)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 2/2/2023 Posts: 5411 Rating: (729)	Dear vorapob, you can record a trace of for example r27 to see the Absolut actual current smoothed. You can open the device trace under your Drive -> Commissioning -> Device trace In the device trace, you can select the signals which you want to record. To start the trace, click on the "play" button.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

7/13/2018 8:45 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	TechTeam Dear vorapob, you can record a trace of for example r27 to see the Absolut actual current smoothed. You can open the device trace under your Drive -> Commissioning -> Device trace In the device trace, you can select the signals which you want to record. To start the trace, click on the "play" button. Dear TechTeam, How can I export this data to .CSV file ? Can I use HMI panel connect to CU320 and selected only require parameter in order to record it ? Thank you. Best Regards, Vorapob
	Best Regards, Vorapob
Suggestion To thank Quote Answer

7/13/2018 9:03 AM	Rate (1)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 2/2/2023 Posts: 5411 Rating: (729)	Dear vorapob, in the trace window, goto "Measurements", then right click on the measurement you want to export. Select "Export measurements" to export it as .CSV
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

7/13/2018 10:14 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	TechTeam Dear vorapob, in the trace window, goto "Measurements", then right click on the measurement you want to export. Select "Export measurements" to export it as .CSV Dear TechTeam, Can I use Siemens PLC in this bus for only record data from Drive ? How can do ? Because I inconvenient to set up PC to record via STARTER. Thank you. Best Regards, Vorapob
	Best Regards, Vorapob
Suggestion To thank Quote Answer

7/13/2018 10:16 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	Attachment CU320_2.jpg (42 Downloads)
	Best Regards, Vorapob
Suggestion To thank Quote Answer

7/13/2018 10:16 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	Attachment CU320_3.jpg (30 Downloads)
	Best Regards, Vorapob
Suggestion To thank Quote Answer

7/13/2018 10:42 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 2/2/2023 Posts: 5411 Rating: (729)	Hello vorapob, the trace in SINAMICS would be the most dynamic way to display your signals. Of course you will need your PC and STARTER. You said that you want to use a HMI. Maybe you could do the following to get an idea of the signal value. Of course, the cycle time of the following is much much lower than the STARTER trace. So, another way would be to send your signal to a PLC via a telegram and then using a time diagram on the HMI to display the signal value.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

7/13/2018 1:50 PM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 1/31/2023 Posts: 984 Rating: (5)	Dear Technology Team, I have no PLC sourcecode and software I don't know how to use this PLC. What is the best way please recommend me ? Best Regards, Vorapob
	Best Regards, Vorapob
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on