Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Data transfer problems !!!!!

Created by: Skyliner at: 7/8/2008 12:15 PM (6 Replies)

Rating (0)

Thanks 0

7 Entries

7/8/2008 12:15 PM	Rate (0)
Skyliner Posts: 5 Rating: (0)	Hi guys we have a milling machine with 820 ga3 M we have pcin and also winpcin and the cable . this is the settings we use . N5010 =00000000 N5011 =11000110 N5012 =00000000 N5013 =11000110 N5014 =00000000 N5015 =00000000 N5016 =00000010 N5017 =00000000 N5018 =00000000 N5019 =11000110 N5020 =00000000 N5021 =11000110 N5022 =00000000 N5023 =00000000 N5024 =00000000 N5025 =00000000 N5026 =00000000 N5027 =00000000 N5028 =00000000 N5029 =00000000 Receiving data or programs is ok( pcin ok) (winpcin ok) ( interface 1 ok ) (interface2 ok ) As you can see we use 4800 bauds 2 stopbits even parity . ( both interface ) Sending programs to the machine is the problem . When we start sending work program to the machine programs (pcin and winpcin )dont send anything . Greetings
Skyliner Posts: 5 Rating: (0)	Last edited by: Skyliner at: 7/8/2008 1:52 PM Last edited by: Skyliner at: 7/8/2008 1:51 PM
Suggestion To thank Quote Answer

7/9/2008 9:50 AM	Rate (0)
Skyliner Posts: 5 Rating: (0)	Nobody has similarproblem ?
Skyliner Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/9/2008 2:36 PM	Rate (0)
CNC Chennai Experienced Member Joined: 12/5/2006 Last visit: 11/7/2022 Posts: 176 Rating: (2)	Try with 5010 & 5011 11000111

Suggestion To thank Quote Answer

7/14/2008 7:56 AM	Rate (0)
Skyliner Posts: 5 Rating: (0)	Hi i have tested but its the same no data transfer ? Other suggentions ? Bye
Skyliner Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/24/2008 6:59 AM	Rate (0)
peter.wang Posts: 5 Rating: (0)	hi, you try set the 5016=00101000
peter.wang Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

7/25/2008 7:43 PM	Rate (0)
nulizhang Platinum Expert Joined: 10/17/2007 Last visit: 3/19/2023 Posts: 3276 Rating: (249)	make sure your cable is no problem. then try to NC->PC transfer some data other than part programs, such as zoa/toa/rpa.... edit them in some line, save and transfer back to machine (PC->NC). TO SEE response. if there is no response. you interfaces may have problem. if NC can get zoa.... you should check you part program header, and try to transfer the prog. which isNOT the sane name in NC..
	Last edited by: nulizhang at: 7/25/2008 7:45 PM Please Help me to understand your question!
Suggestion To thank Quote Answer

7/26/2008 3:48 PM	Rate (0)
Sanjoy 4m India Posts: 55 Rating: (2)	I have same type of experiance. found same RS232 settingalways not working for both receiving and sending of data. slower baud rate some time works. of course, data header line should not be changed any way.
Sanjoy 4m India Posts: 55 Rating: (2)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on