Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Error 0x177 Tiaportal v12

Created by: marco23 at: 4/10/2014 3:06 PM (6 Replies)

Rating (0)

Thanks 0

7 Entries

4/10/2014 3:06 PM	Rate (0)
marco23 Posts: 24 Rating: (0)	Someone could give me this error diagnosis 0X177 tiaportal v12, can not make a plc DISCHARGE the CPU315-0AB0 6ES7-2AH14. Get an error message too large operating system. Attachment F31.jpg (121 Downloads)
marco23 Posts: 24 Rating: (0)	Last edited by: marco23 at: 4/10/2014 3:55 PM Last edited by: marco23 at: 4/10/2014 3:33 PM
Suggestion To thank Quote Answer

4/10/2014 3:47 PM	Rate (0)
marco23 Posts: 24 Rating: (0)	testing with step7 also leaves the problem that can not be argar the sdb7, error 13:4589. Attachment f33.jpg (99 Downloads)
marco23 Posts: 24 Rating: (0)	Last edited by: marco23 at: 4/10/2014 3:58 PM
Suggestion To thank Quote Answer

4/10/2014 4:58 PM	Rate (0)
H_a_m_m_y Experienced Member Joined: 8/19/2013 Last visit: 8/26/2024 Posts: 148 Rating: (11)	Hello marco23 please post your screenshots in English / switch your user interface language to English. Thx/Regards

Suggestion To thank Quote Answer

4/10/2014 10:02 PM	Rate (0)
marco23 Posts: 24 Rating: (0)	FAIL IN STEP 7 V5.5, is a new CPU 6ES7 2AH14 0AB0, the PLC not have MMC. according to this page says that you need the MMC, https://support.automation.siemens.com/WW/llisapi.dll?func=cslib.csinfo&objId=32635811&nodeid0=33516848&load=treecontent&prodLstObjId=32635811&lang=en&siteid=cseus&aktprim=0&objaction=csview&extranet=standard&viewreg=WW you can not download the SDB7 in the PLC. Attachment F21.jpg (89 Downloads)
marco23 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

4/11/2014 12:09 AM	Rate (0)
marco23 Posts: 24 Rating: (0)	I HAVE GIVEN ME WITH SURPRISE THAT THE PROGRAM TIAPORTAL V12 HAVE SAME PROBLEM. I can not download hardware. CAN NOT LOAD THE SDB7 OPERATING SYSTEM TOO BIG Error code 0x117, I find this error ... Attachment F22.jpg (91 Downloads)
marco23 Posts: 24 Rating: (0)	Last edited by: marco23 at: 4/11/2014 12:10 AM
Suggestion To thank Quote Answer

4/11/2014 9:34 AM	Rate (0)
H_a_m_m_y Experienced Member Joined: 8/19/2013 Last visit: 8/26/2024 Posts: 148 Rating: (11)	IfStep V5.5 and V12give the same message there is soemthing wrong in the configuration. Save and compile normally should show you the faults in the configuration but in this case it does not. It is correct, becauseif you want to use a 31x CPU you need a MMC !

Suggestion To thank Quote Answer

4/11/2014 3:32 PM	Rate (0)
marco23 Posts: 24 Rating: (0)	hello, I used a MMC another another PLC CPU 315, but when you insert the MMC the SF LED lit put the selector in the MRES erase fault, but with the memory set can not connect online with the PLC. Any suggestions, remember to reset the MMC may have other applications.
marco23 Posts: 24 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on