Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

error trying to move a varible

Created by: femo at: 9/29/2011 4:16 PM (11 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

12 Entries

Entries per page: 10 | all

9/29/2011 4:16 PM	Rate (0)
femo Advanced Member Joined: 10/16/2010 Last visit: 11/28/2023 Posts: 63 Rating: (0)	Hello, I have this eror o r warning when I do this instruction. Im working with V11. Same instruction on V10.5 has no error. is this notallowed in V11??? Thanks femo Attachment error.JPG (308 Downloads)

Suggestion To thank Quote Answer

9/29/2011 5:46 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 12/8/2023 Posts: 4284 Rating: (1381)	Hi, The V11 make many tests and checks that V10.5 doesn't make. It is just a warning, it is not a error. The V11 is tell you just that there is no simbolic variablewith absolut addressDB1.DBD1. It should be that you have make a mistake in your program or it seens that you know very well the features of the tool and access absolutly a not declarate variable. The V11 could not determine itself what is the case, so it gives this message. If you intends to address absolutly a not simbolic declareted variable, just ignore this message.
	Last edited by: Pegaia at: 9/29/2011 5:49 PM Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

9/29/2011 8:31 PM	Rate (0)
femo Advanced Member Joined: 10/16/2010 Last visit: 11/28/2023 Posts: 63 Rating: (0)	Yes, actually it's a warning not an error. But if I download the program like this. It doesnt work fine, began to have problems, actually the last post I made about error 46 showing in the screen was because of this(is my belive). I take out the warning from the program and began to work fine. Is strange but happens.

Suggestion To thank Quote Answer

9/30/2011 9:44 AM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 12/1/2023 Posts: 8596 Rating: (1140)	Dear femo, Are you sure about the absolute address DB1.DBD1? Perhaps it must be DB1.DBD0 or DB1.DBD2 (Most of the time it starts with even address) Best regards, Wizard

Suggestion To thank Quote Answer

9/30/2011 5:20 PM	Rate (0)
femo Advanced Member Joined: 10/16/2010 Last visit: 11/28/2023 Posts: 63 Rating: (0)	Attach is an example of what Im talking about Attachment test.zip (289 Downloads)

Suggestion To thank Quote Answer

10/3/2011 5:52 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 12/8/2023 Posts: 4284 Rating: (1381)	Hi, DB1.DBD1 contains from DBX1.0 to DBX4.7. Your DB1 has up to DBX6.1. In this case, if you really want overwrite DBX1.0 to 4.7 with the constant DW#16#1, it is ok. Just desconsidere the warning.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer

10/3/2011 6:20 PM	Rate (0)
femo Advanced Member Joined: 10/16/2010 Last visit: 11/28/2023 Posts: 63 Rating: (0)	I had try it already but don't work well. Thanks femo

Suggestion To thank Quote Answer

10/3/2011 7:11 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/9/2023 Posts: 13994 Rating: (2282)	femo I had try it already but don't work well. Thanks femo I loaded your test program into a S7-1214C DC/DC/RLY with FW 2.1 using TIA Portal V11 Basic SP1 Update 2. Here's the watch table results showing it did work as written. I expanded the watch table to help clarify how the data block's data is working with your MOVE command. Attachment Test_MOVE_WatchTable.jpg (365 Downloads)
	science guy
Suggestion To thank Quote Answer

10/3/2011 7:32 PM	Rate (0)
femo Advanced Member Joined: 10/16/2010 Last visit: 11/28/2023 Posts: 63 Rating: (0)	Thanks everybody. femo

Suggestion To thank Quote Answer

10/3/2011 9:34 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/9/2023 Posts: 13994 Rating: (2282)	femo Thanks everybody. femo Did you get it to do what you wanted it to do? Please post your results!
	science guy
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on