Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

ET200S - AI RTD and AI U ST errors

Created by: mpsautomation at: 5/14/2012 11:54 AM (7 Replies)

Rating (0)

Thanks 0

8 Entries

5/14/2012 11:54 AM	Rate (0)
mpsautomation Posts: 6 Rating: (0)	Hello, i'm using some ET200S with "2AI x RTD HF" and "2AI x U ST". I'd like to know if the probe is connected or faulty. How it's possible? Thank you.
mpsautomation Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

5/14/2012 12:57 PM	Rate (0)
viralpatel Silver Member Joined: 11/18/2010 Last visit: 8/5/2022 Posts: 523 Rating: (31)	means?? you want to know how to check wiring fault etc...please clear regards, viral

Suggestion To thank Quote Answer

5/14/2012 2:24 PM	Rate (0)
mpsautomation Posts: 6 Rating: (0)	viralpatel means?? you want to know how to check wiring fault etc...please clear regards, viral Excuse for not being clear, but my intetn is to check wiring fault.
mpsautomation Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

5/14/2012 9:24 PM	Rate (0)
gre_m Posts: 947 Rating: (45)	What im151 are you using? basic, High feature or standart? you have PM-e? which terminal module you use? need MLFB.
gre_m Posts: 947 Rating: (45)	Last edited by: gre_m at: 5/14/2012 9:25 PM
Suggestion To thank Quote Answer

5/14/2012 9:26 PM	Rate (0)
IBN-Service Posts: 8946 Rating: (995)	mpsautomation viralpatel means?? you want to know how to check wiring fault etc...please clear regards, viral Excuse for not being clear, but my intetn is to check wiring fault. Enable wire break detection (Diag in HW config)
IBN-Service Posts: 8946 Rating: (995)
Suggestion To thank Quote Answer

5/15/2012 7:44 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 4/12/2023 Posts: 10221 Rating: (1176)	Hello, In forum have a lot examples how to read wire break detection and eventually to display on HMI after. Put in search - 'read wire break'. Best regards, Hristo Mihalev Attachment test.jpg (72 Downloads)
	Last edited by: UMENCHO at: 5/15/2012 7:46 AM
Suggestion To thank Quote Answer

5/15/2012 1:00 PM	Rate (0)
mpsautomation Posts: 6 Rating: (0)	gre_m Whatim151are you using? basic, High feature or standart? you have PM-e? which terminal module you use? need MLFB. Hello, my configuration for one of many is: IM 151-1 HF PM-E DC24V 8DI x DC24V 8DI x DC24V PM-E DC24V 2RO x NO/NC 24/230V / 5A PM-E DC24V 2AI x RTD HFwith a ni1000 probe (my interest) 2AI x U ST with a 0..10V %UR probe (my interest) 2AO x U ST UMENCHO In forum have a lot examples how to read wire break detection and eventually to display on HMI after. Put in search - 'read wire break'. Best regards, Hristo Mihalev i'll search and read.
mpsautomation Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

5/16/2012 1:52 PM	Rate (0)
Prats Posts: 272 Rating: (4)	mpsautomation gre_m Whatim151are you using? basic, High feature or standart? you have PM-e? which terminal module you use? need MLFB. Hello, my configuration for one of many is: IM 151-1 HF PM-E DC24V 8DI x DC24V 8DI x DC24V PM-E DC24V 2RO x NO/NC 24/230V / 5A PM-E DC24V 2AI x RTD HFwith a ni1000 probe (my interest) 2AI x U ST with a 0..10V %UR probe (my interest) 2AO x U ST UMENCHO In forum have a lot examples how to read wire break detection and eventually to display on HMI after. Put in search - 'read wire break'. Best regards, Hristo Mihalev i'll search and read. HAVE YOU CHECK THE WIRING USING MULTIMETER...IT OF GREAT HELP IN COMMISSIONING.
Prats Posts: 272 Rating: (4)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on