Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Fault 1910 and 1912

Created by: SebOber at: 4/18/2012 4:19 PM (17 Replies)

Rating (2)

Thanks 4

Result pages:: |; 1 | 2; |

18 Entries

Entries per page: 10 | all

4/18/2012 4:19 PM	Rate (1)
SebOber Posts: 34 Rating: (3)	repost from different product conference Hello, I'm working on a two axis project, I have two 1FK7060 motors on a double motor module. I've configured everything and and am able to take control of the both motors through the sinamics side and simotion side from the control panels. However when I give control to my program and go to move the motors I get fault 1910 and 1912. They are configured with the siemens telegram 105 message frame. I've gone through and checked all the parameters that the help topics from the error codes suggests. But I still can not find the problem. I've uploaded the fault logs in .zip format.I've included a few logs from different times I've encountered the errors. Also included is the diagnostic buffer from the D425. In the diagnostics buffer the events dated 4-13-12 are relevant the other fault logs uploaded. I really hope someone has an answer. =) I've already spent many hours trying to correct this problem. Also, I had worked with a D435 six axis system and had the same problem. We had a siemens rep at the site helping with some other issues and he noticed the fault 1910/1912 and clicked a few things changed some setting and suddenly it was gone. Unfortunetly, I did not pay attention nor did he tell me what he did. Thanks in advanced!! -Seb Attachment fault logs.zip (608 Downloads)
SebOber Posts: 34 Rating: (3)
Suggestion To thank Quote Answer

4/18/2012 4:26 PM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Hello, the reason for 1910/1912 in your case is: Program missing for a task TechnologicalFaultTask When you activate the gearing a technological Falt occurs and no program is inth fault task, so the PLC switch to operationmode STOP and the faults occurs. Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 2 thankful Users SebOber El Solvente

4/20/2012 6:58 AM	Rate (0)
SebOber Posts: 34 Rating: (3)	Thanks Christoph, I inserted the approriate programs into the fault tasks and fixed my problem straight away. RESOLVED
SebOber Posts: 34 Rating: (3)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users S_Moderator

7/6/2019 2:30 PM	Rate (0)
1987vasanth23KUMAR Member Joined: 6/27/2011 Last visit: 11/28/2024 Posts: 4 Rating: (0)	Could u please tell me how you solved this issue

Suggestion To thank Quote Answer

7/6/2019 2:34 PM	Rate (0)
1987vasanth23KUMAR Member Joined: 6/27/2011 Last visit: 11/28/2024 Posts: 4 Rating: (0)	Please explain how to do this....I am not familiar with simotion could you please help me out

Suggestion To thank Quote Answer

7/7/2019 8:11 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	which problem you have? Whoixh simotion you use, which version? Whixh faults you get? Any screen or diagnostic buffer? Regards Christoph

Suggestion To thank Quote Answer

6/11/2020 10:53 AM	Rate (0)
Mustafa.N Member Joined: 6/5/2020 Last visit: 7/26/2023 Posts: 1 Rating: (0)	hello friends, I have the same problem. I used simotion D 435-2 DP/PN. I assigned a blank mcc chart into faulttask, but my problem continues. Since I use this kit for testing, I also need to set drives-> functions-> line contactor control-> infeed operation to 1 to run with axis-> contral panel. I can run it later. but when I open the control operation state section to run the mcc chart block, it goes into run state but the engine does not work. then when I put it into stop state, I get the errors 1910,1912 and 1915. Can you help me? Information: PLC_1 -- OK Fault: 10.06.20 16:16:33:726 SINAMICS_Integrated_1 : S_INF_02 -- 1910 : Fieldbus: setpoint timeout Fault: 10.06.20 16:16:33:726 SINAMICS_Integrated_1 : SERVO_04 -- 1910 : Fieldbus: setpoint timeout Fault: 10.06.20 16:16:33:706 SINAMICS_Integrated_1 : SERVO_04 -- 1915 : PB/PN: clock cycle synchronous operation sign-of-life failure drive object 1 Fault: 10.06.20 16:16:33:704 SINAMICS_Integrated_1 : Control_Unit -- 1915 : PB/PN: clock cycle synchronous operation sign-of-life failure drive object 1 Fault: 10.06.20 16:16:33:704 SINAMICS_Integrated_1 : SERVO_04 -- 1912 : PB/PN: clock cycle synchronous operation sign-of-life failure Fault: 10.06.20 16:15:33:414 SINAMICS_Integrated_1 : S_INF_02 -- 1910 : Fieldbus: setpoint timeout Warning: 06.01.00 00:30:45:318 SINAMICS_Integrated_1 : S_INF_02 -- 6400 : Infeed: Line supply data identification selected/active
	Last edited by: Mustafa.N at: 06/11/2020 10:55:44
Suggestion To thank Quote Answer

6/12/2020 8:10 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Mustafa.N hello friends, I have the same problem. I used simotion D 435-2 DP/PN. I assigned a blank mcc chart into faulttask, but my problem continues. Since I use this kit for testing, I also need to set drives-> functions-> line contactor control-> infeed operation to 1 to run with axis-> contral panel. I can run it later. but when I open the control operation state section to run the mcc chart block, it goes into run state but the engine does not work. then when I put it into stop state, I get the errors 1910,1912 and 1915. Can you help me? Information: PLC_1 -- OK Fault: 10.06.20 16:16:33:726 SINAMICS_Integrated_1 : S_INF_02 -- 1910 : Fieldbus: setpoint timeout Fault: 10.06.20 16:16:33:726 SINAMICS_Integrated_1 : SERVO_04 -- 1910 : Fieldbus: setpoint timeout Fault: 10.06.20 16:16:33:706 SINAMICS_Integrated_1 : SERVO_04 -- 1915 : PB/PN: clock cycle synchronous operation sign-of-life failure drive object 1 Fault: 10.06.20 16:16:33:704 SINAMICS_Integrated_1 : Control_Unit -- 1915 : PB/PN: clock cycle synchronous operation sign-of-life failure drive object 1 Fault: 10.06.20 16:16:33:704 SINAMICS_Integrated_1 : SERVO_04 -- 1912 : PB/PN: clock cycle synchronous operation sign-of-life failure Fault: 10.06.20 16:15:33:414 SINAMICS_Integrated_1 : S_INF_02 -- 1910 : Fieldbus: setpoint timeout Warning: 06.01.00 00:30:45:318 SINAMICS_Integrated_1 : S_INF_02 -- 6400 : Infeed: Line supply data identification selected/active hi if you put the cpu to stop is ok that this alarms are coming up, this is no problem. regards christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Mustafa.N

6/22/2020 4:25 AM	Rate (0)
o0yuming0o Advanced Member Joined: 3/30/2014 Last visit: 11/19/2024 Posts: 93 Rating: (3)	Hello ChristophD In my project , Fault 1910 of Infeed can not be reset by the FB _LineModule_control after download program and CPU run again(In most cases this alarm will disappear automatically after download program and CPU run again). But it can be reset by the Acknowledge button in the "Alarms" window of SCOUT. The solutions provided by local technical support are as follows: ① x132.13 configure as output point in “Input/Output” of CU ②Declare an output variable “boInfeedReset” in the address list and configure it for X132.13. ③Configure r722.15 for p2102 in "Expert list" of CU. (r722.15=X132.13) Now you can reset other devices mounted on CU320 through variable “boInfeedReset” . I configured some measuring input in the input/output of CU. The local technical support told me that why I can not reset Fault 1910 of Infeed by FB _LineModule_control. Also I can not reset it by directly operating the reset bit on the telegram. Is there a description of this situation in the technical manual? Software: SIMOTION SCOUT TIA V5.3.1 Hardware: D455-2, firmware version：V5.3 CU320-2 PN, firmware version: V5.2
	Last edited by: o0yuming0o at: 06/22/2020 04:26:26 Last edited by: o0yuming0o at: 06/22/2020 04:27:53 Last edited by: o0yuming0o at: 06/22/2020 04:30:53
Suggestion To thank Quote Answer

6/22/2020 6:15 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/20/2024 Posts: 22482 Rating: (3039)	Hello, which infeed you use exactly? which Telegram you use for the Infeed? Do you get some error if you execute the FB to acknowledge the Fault? Regards Christoph

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on