Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

FC5 AG_SEND with CP 343-1 v1.0.3

Created by: Antoine.R at: 2/19/2013 2:21 PM (7 Replies)

Rating (0)

Thanks 1

8 Entries

2/19/2013 2:21 PM	Rate (0)
Antoine.R Posts: 10 Rating: (0)	Hello, I'm actually trying to send some bytes (data are ascii codes) to a smartmotor via an industrial ethernet network. My station is a CPU315 with a CP 343-1 and a switchx208. To do this I'm using the FC5 AG_SEND from the library. The "DONE" bit goes to 1, meaning it worked but the motor doens't see anything. I used wireshark to see what happens but I can say that really nothing from the CP 341 goes out. I wanted to know if this version of this SIMATIC NET is able to support the FC5 AG_SEND. I also don't any blocs into the CP 343-1, I don't know if there should be some. Best regards
Antoine.R Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

2/19/2013 2:39 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 3/19/2025 Posts: 10239 Rating: (1183)	Antoine.R Hello, I'm actually trying to send some bytes (data are ascii codes) to a smartmotor via an industrial ethernet network. My station is a CPU315 with a CP 343-1 and a switchx208. To do this I'm using the FC5 AG_SEND from the library. The "DONE" bit goes to 1, meaning it worked but the motor doens't see anything. I used wireshark to see what happens but I can say that really nothing from the CP 341 goes out. I wanted to know if this version of this SIMATIC NET is able to support the FC5 AG_SEND. I also don't any blocs into the CP 343-1, I don't know if there should be some. Best regards How do you program the communication blocks FC5 and FC6?

Suggestion To thank Quote Answer

2/19/2013 3:26 PM	Rate (0)
Antoine.R Posts: 10 Rating: (0)	Unfortunately, The 1EX10-0XE0 I'm using doens't appear in this list.
Antoine.R Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

2/19/2013 3:33 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 3/19/2025 Posts: 10239 Rating: (1183)	My idea was to check your settings there.1EX11-0XE0 is a successor product of 1EX10. It supports both functions. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

2/19/2013 4:40 PM	Rate (0)
Antoine.R Posts: 10 Rating: (0)	Settings are good, that's the problem. However I would have an error status I guess. Best regards
Antoine.R Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

2/19/2013 4:52 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 3/19/2025 Posts: 10239 Rating: (1183)	In AG_SEND what do you receive like a status code?

Suggestion To thank Quote Answer

2/20/2013 4:42 PM	Rate (0)
Antoine.R Posts: 10 Rating: (0)	I had 8181 like it was going too fast. I found the solution after a few hours (ISO problem). Anyway, do you know where I can find the Extended ascii table used by STEP7 ? Because I wan't to use the 80 (hexa) ascii caracter (in standard extended ascii table) but STEP7 uses it as C7 caracter (hexa). So I would like to find which caracter is the one I'm looking for. Thanks for your help
Antoine.R Posts: 10 Rating: (0)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users umencho

2/20/2013 5:18 PM	Rate (0)
umencho Diamond Expert Joined: 3/21/2006 Last visit: 3/19/2025 Posts: 10239 Rating: (1183)	Did you search in Simatic Manager Help files? I thought there has a table. or that was in other software. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on