Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

freezes the card input and output analog

Created by: ElectroTCC at: 4/3/2013 5:04 PM (12 Replies)

Rating (1)

Thanks 5

Result pages:: |; 1 | 2; |

13 Entries

Entries per page: 10 | all

4/3/2013 5:04 PM	Rate (0)
ElectroTCC Regular Member Joined: 6/4/2010 Last visit: 1/10/2023 Posts: 33 Rating: (0)	Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem?
	Last edited by: ElectroTCC at: 4/3/2013 5:05 PM Dany Thibeault
Suggestion To thank Quote Answer

7/13/2013 2:31 PM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 10/3/2023 Posts: 4477 Rating: (830)	ElectroTCC Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem? Hello, It seems that there are some bugs in your Analog Scaling and Un-Scaling functions. Please attach screen shots of these function here.
	Ayman Elotaify
Suggestion To thank Quote Answer

7/13/2013 3:09 PM	Rate (0)
SolutionFinder Posts: 559 Rating: (87)	You can check the count values for Analog Inputs & Also give count values directly to analog output. Check your hardware configuration also. Have you selected 4..20 mA at your channel settings? If it is Ok then use count value 0 as 4 mA & 27648 as 20 mA & then check the result.
SolutionFinder Posts: 559 Rating: (87)
Suggestion To thank Quote Answer

7/13/2013 3:32 PM	Rate (0)
Amit_86 Platinum Member Joined: 3/18/2008 Last visit: 8/25/2022 Posts: 1750 Rating: (270)	ElectroTCC Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem? In STEP 7 (TIA Portal) V11, how can you scale integer values in real numbers and real values in integer numbers for analog measurements?
	VANDE MATARAM.....
Suggestion To thank Quote Answer

7/15/2013 6:45 AM	Rate (0)
viralpatel Silver Member Joined: 11/18/2010 Last visit: 8/5/2022 Posts: 523 Rating: (31)	ElectroTCC Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem? Have you checked controller is in RUN mode or giving any error/warning ? VP

Suggestion To thank Quote Answer

7/15/2013 6:54 AM	Rate (0)
DS SURESH KUMAR Bronze Member Joined: 4/17/2012 Last visit: 9/7/2023 Posts: 474 Rating: (10)	ElectroTCC Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem? Hi, Now you connected the Module with the field??? Please check the HW configuration of AO and AI which option you selected? If you configure any output address in scalling blocks then delete that addess and after that try to force from VAT table

Suggestion To thank Quote Answer

7/15/2013 7:13 AM	Rate (0)
@shish Bronze Member Joined: 9/16/2011 Last visit: 9/10/2022 Posts: 291 Rating: (6)	ElectroTCC Hello, I program an entire new controller with 2racks and TP1200 Comfort and Profibus. All my I / O function except the two analog cards with card entry 6ES7 331-7NF00-0AB0 and output card 6ES7 332-5HF00-0AB0 I have no error according to the Diagnostic and when I do a force in the table Forcing my card output gives me 4.0 mA continuously. For the input card, I simulates a 4 @ 20 mA and the program, nothing happens. Always 0%. Note that I program with the TIA Portal V11 An idea of the problem? Dear, Proceed step by step as explained by our experts. Check the Hardware configuration for current input/output and for 4-20mA range. Also check that whether CPU is showing any error. Give input mA to the Analog input terminals and check the count 0-27648 for 4-20 mA Also for analog output give each channel a count value between 0 and 27648 and check the mA at output terminals. Reg, Ashish
	Reg, @shish --- If satisfied with reply, Rate it ! If problem solved, hit THANK !
Suggestion To thank Quote Answer

7/15/2013 7:51 AM	Rate (0)
Ton Verra Gold Member Joined: 4/20/2007 Last visit: 8/30/2023 Posts: 724 Rating: (40)	Also. You say simulate 4..20mA signal. How do you simulate?

Suggestion To thank Quote Answer

7/15/2013 7:56 AM	Rate (1)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 7/12/2023 Posts: 10221 Rating: (1177)	Ton Verra Also. You say simulate 4..20mA signal. How do you simulate? It is possible to connect external source for 4-20mA to AI. Sometimes I am using FLUKE 743B Calibrator for that reason.
	Last edited by: UMENCHO at: 7/15/2013 7:57 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Tomy Master

7/15/2013 8:09 AM	Rate (0)
Ton Verra Gold Member Joined: 4/20/2007 Last visit: 8/30/2023 Posts: 724 Rating: (40)	I know. I do to. Also easy to do this wrong. Polarity, type of simulation, feeding from Fluke or not. Or maybe he was using PLCSIM to simulate. There is more then one way to do thing..

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users UMENCHO

|

Share this page:

Share this page on...

Follow us on