Skip to Content

SiePortal

The integrated platform for your product selection, buying and support workflow - bringing together Industry Mall and Online Support.

SiePortalDeutsch

Search

Home
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menu temporary not available
- Menue temporary not available
- {{item.title}}

Products & Services
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Support Support
{{(apiData.Support | filter:{'rank':1}:true)[0].title}} Support
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
MySiePortal MySiePortal
{{(apiData.MySiePortal | filter:{'rank':1}:true)[0].title}} MySiePortal
- Menu temporary not available
- Menue temporary not available
- {{item.title}}
Cart ({{apiData.CartCount}})

Navigation

G120/CU240E-2 PN unable to restore factory Safety settings

Created by: lukraj at: 7/9/2020 9:53 PM (10 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

7/9/2020 9:53 PM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	Hello! Something must have gone wrong somewhere whilst configuring the drive via TIA v15 and the drive simply doesn't cooperate. To cut the long story short, I want to restore the factory settings, including safety configuration. Do I understand correctly that the safety should be disabled when factory settings are restored? Having performed Safety parameters reset via the Drive commissioning screen in TIA, which requires password, and after a power cycle, the settings are still where they were before the reset. I also can't change in active commissioning any safety settings as they are being overwritten after a second, or so. Can somebody please advise if there is a better, more direct way to bring the factory settings back? Or there is something that needs toggling before that I'm overlooking? Thanks!
	Last edited by: lukraj at: 07/09/2020 22:14:39
Suggestion To thank Quote Answer

7/10/2020 8:15 AM	Rate (0)
BoletusEdulis Silver Member Joined: 6/10/2015 Last visit: 4/24/2025 Posts: 472 Rating: (101)	Hi, check the attachment: the safety factory reset has its own command. Did you do it through this command? Attachment SafeReset.PNG (480 Downloads)
	B. Edulis --- If you have a doubt, there is no doubt
Suggestion To thank Quote Answer

7/10/2020 9:29 AM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	That's exactly what I did, as per the manual.

Suggestion To thank Quote Answer

7/10/2020 10:24 AM	Rate (0)
BoletusEdulis Silver Member Joined: 6/10/2015 Last visit: 4/24/2025 Posts: 472 Rating: (101)	I can't see anything clearer than this link: https://support.industry.siemens.com/cs/gb/en/view/46607912
	Last edited by: Jen_Moderator at: 07/10/2020 10:38:01 Optimized link. B. Edulis --- If you have a doubt, there is no doubt
Suggestion To thank Quote Answer

7/10/2020 10:53 AM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	Thanks. I tried it before, but re-tried again. When trying to set P10=30 to activate resetting of the settings, the CU return 'invalid' and value doesn't get accepted. What is preventing the drive from accepting the reset request...?

Suggestion To thank Quote Answer

7/10/2020 11:08 AM	Rate (0)
BoletusEdulis Silver Member Joined: 6/10/2015 Last visit: 4/24/2025 Posts: 472 Rating: (101)	Dumb question but mandatory: the drive is in off-state, right? Do you get any alarm? Can you see any in the buffer diag and report it here?
	Last edited by: BoletusEdulis at: 07/10/2020 11:12:42 B. Edulis --- If you have a doubt, there is no doubt
Suggestion To thank Quote Answer

7/10/2020 11:12 AM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	BoletusEdulis Dumb question but mandatory: the drive is in off-state, right? Off-state you mean the connected motor is not running? If so, then yes, it is in off-state.

Suggestion To thank Quote Answer

7/10/2020 11:14 AM	Rate (0)
BoletusEdulis Silver Member Joined: 6/10/2015 Last visit: 4/24/2025 Posts: 472 Rating: (101)	lukraj BoletusEdulis Dumb question but mandatory: the drive is in off-state, right? Off-state you mean the connected motor is not running? If so, then yes, it is in off-state. Put it in SAFE STATE (STO blocks energy flow to the motor)
	B. Edulis --- If you have a doubt, there is no doubt
Suggestion To thank Quote Answer

7/10/2020 11:20 AM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	BoletusEdulis lukraj BoletusEdulis Dumb question but mandatory: the drive is in off-state, right? Off-state you mean the connected motor is not running? If so, then yes, it is in off-state. Put it in SAFE STATE (STO blocks energy flow to the motor) Supply to the Power Unit is disconnected, Profinet cables disconnected, drive power cycled. Can't see any run command coming from anywhere, but I sense it will be something dumb...

Suggestion To thank Quote Answer

7/10/2020 12:05 PM	Rate (0)
lukraj Regular Member Joined: 1/21/2015 Last visit: 12/12/2024 Posts: 6 Rating: (0)	BoletusEdulis Do you get any alarm? Can you see any in the buffer diag and report it here? There is an active alarm asking for the Acceptance Test to be completed.

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on