Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

g120c pn not assigned

Created by: Jackcaress at: 8/2/2016 6:12 PM (15 Replies)

Rating (4)

Thanks 4

Result pages:: |; 1 | 2; |

16 Entries

Entries per page: 10 | all

8/2/2016 6:12 PM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	Good evening forum, I have been battling with an g120c pn for a while now and after going through a couple of manuals my problem still insists, Im trying to move the g120c pn with a 1200 but on tia portal v13 it comes up as not assigned and the red BF light keeps on flashing on the device, I have changed the ip´s and names of them all with no luck the light keeps on blinking Can some one help me with this to stop me from going crazy Thank you in advance

Suggestion To thank Quote Answer

8/2/2016 6:47 PM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	Hello, what do you mean whit no assigned? Which PLC Version do you have in the Project? In Networkview if you click on "Not assigned " the available PN Controllers should be dispplayed. Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Jackcaress

8/5/2016 8:41 AM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	Sorry about not getting back to you right away, i had to stop with this problem and solve another one. below is an image of the problem im having, in the diagnostics part of the g120c pn it says the same ``not assigned (no asignado)´´ Any idea what this could be?

Suggestion To thank Quote Answer

8/5/2016 8:49 AM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	Attachment asignado.PNG (129 Downloads)

Suggestion To thank Quote Answer

8/5/2016 8:55 AM	Rate (1)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 12/1/2023 Posts: 8596 Rating: (1139)	Hello Jackcaress, You will have to click on the "not assigned", then you will have a pop up with possible Profinet Controllers. Now you can choose one. Then you will see it is assigned to a Profinet Controller. (Like earlier mentioned.) Best regards, Wizard

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Jackcaress

8/5/2016 9:15 AM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	Hi, if you click on "Not assigned" and no Controller is displayed then please check the Version of your configured PLC! A S7-1200 V1.0 can't be used as IO-Controller , if this is the problem update the PLC to Version V2.x. Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Jackcaress

8/5/2016 9:33 AM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	After clicking on the not assigned button it says that i dont have a controler, what is the controler exactly?

Suggestion To thank Quote Answer

8/5/2016 9:33 AM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	Attachment asignado.PNG (108 Downloads)

Suggestion To thank Quote Answer

8/5/2016 9:36 AM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	Hello, the Controller is normaly the PLC which control the Devices and the PROFINET Network, is similar to a DP Master in the PROFIBUS. Have you check the Version of the PLC you have in the project? If i V1.0 or higher? Regards Christoph

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Jackcaress

8/5/2016 9:36 AM	Rate (0)
Jackcaress Silver Member Joined: 3/12/2015 Last visit: 11/29/2023 Posts: 529 Rating: (15)	Ive just seen your message now, i think the version of the software is v4.1 ChristophD Hi, if you click on "Not assigned" and no Controller is displayed then please check the Version of your configured PLC! A S7-1200 V1.0 can't be used as IO-Controller , if this is the problem update the PLC to Version V2.x. Regards Christoph

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on