Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Hardware Configuration issue

Created by: Engr Umair at: 5/25/2014 7:32 AM (23 Replies)

Rating (0)

Thanks 2

Result pages:: |; 1 | 2 | 3; |

24 Entries

Entries per page: 10 | 20 | all

5/25/2014 7:32 AM	Rate (0)
Engr Umair Posts: 50 Rating: (0)	1. i have 2 CPU 315-2DP which are installed on machine. When i upload the station to PC All the blocks and Hardware configuration correctly uploaded to PC. But when i upload the station to PC from 2nd CPU. Their occurs an ERROR 2000.It upload all the blocks but hardware configuration is not complete. Where Masterdrives MC are attached on Profibus but its not showing in Hardware configuration ! Please guide me whats the issue.Error pic is also attached When i upload the station blocks are uploaded but hardware is not complete its not showing Master Drive MC Please help me out Thanks
Engr Umair Posts: 50 Rating: (0)	Last edited by: Engr Umair at: 5/26/2014 8:39 AM
Suggestion To thank Quote Answer

5/25/2014 7:36 AM	Rate (0)
Engr Umair Posts: 50 Rating: (0)	Picture Attachment errorrr.jpg (299 Downloads)
Engr Umair Posts: 50 Rating: (0)
Suggestion To thank Quote Answer

5/25/2014 8:09 AM	Rate (0)
Ste39 Platinum Member Joined: 1/21/2013 Last visit: 10/1/2023 Posts: 4617 Rating: (701)	Hello Have you already seen this perhaps might help you: /tf/WW/en/Posts/39888

Suggestion To thank Quote Answer

5/25/2014 8:23 AM	Rate (0)
PDGANGANI Posts: 165 Rating: (19)	Engr Umair 1. i have 2 CPU 315-2DP which are installed on machine. When i upload the station to PC All the blocks and Hardware configuration correctly uploaded to PC. But when i upload the station to PC from 2nd CPU. Their occurs an ERROR 2000.It upload all the blocks but hardware configuration is not complete. Where Masterdrives MC are attached on Profibus but its not showing in Hardware configuration ! Please guide me whats the issue.Error pic is also attached When i upload the station blocks are uploaded but hardware is not complete its not showing Master Drive MC Please help me out Thanks Hello, You should know that it is very important to know that original program in CPU is program in Which version of Simatic Manager. If you are using latest version then some times this kind of error comes...i also faced same kind of errors. Due to version change you first need to check tht Master drive MC is available in your current version or not....If it is available but in your upleaded hardware showing DP-Norm then you just need to reconfigure Your Drive with same parameters only in the Hardware. Hope it helps!!!
PDGANGANI Posts: 165 Rating: (19)
Suggestion To thank Quote Answer

5/25/2014 11:29 AM	Rate (0)
SolutionFinder Posts: 559 Rating: (87)	There must be possibility of MPI address duplication. If you upload the backup from first CPU say with MPI address 2 & in the same project if you upload the backup from other CPU with same MPI address then it could not be uploaded in the same project. You must have to create new project then upload.
SolutionFinder Posts: 559 Rating: (87)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users PDGANGANI

5/25/2014 12:55 PM	Rate (0)
@shish Bronze Member Joined: 9/16/2011 Last visit: 9/10/2022 Posts: 291 Rating: (6)	Try to upload the program from the CPU individually. I mean, PG connected to CPU one at a time using MPI.
	Last edited by: @shish at: 5/25/2014 12:56 PM Reg, @shish --- If satisfied with reply, Rate it ! If problem solved, hit THANK !
Suggestion To thank Quote Answer

5/26/2014 7:44 AM	Rate (0)
Engr Umair Posts: 50 Rating: (0)	I am trying to upload the Station from CPU 315-2DP ( 6ES7 315-2AG10-0AB0 ) with Simatic Step 7 Version 5.5 I can upload OBs,FBs,FCs,...but when I upload Hardware an error window appears with following content: 2000) error while uploading the the configuration to the programming device (PG). Do you want to continue? and then when I click the help button help on massage 13 : 77 appears Please be informed the CPU is still running without any faults. I have tried to upload hardware with HwConfig too but the same errors taked place. Also I tried to change PG/PC setting but in all correct ones the same error existed. Also from somewhere i also have read Drive ES PCS 7 this required to upload the hardwre station. Is it required ? Thanks
Engr Umair Posts: 50 Rating: (0)	Last edited by: Engr Umair at: 5/26/2014 7:44 AM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Lee.best

5/26/2014 7:58 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 7/12/2023 Posts: 10221 Rating: (1177)	Yes, it seems you need to have installed DriveES package. In order to be sure ask who made the last changes in that project for confirmation. Becase that package is not free. There is no way to upload the project without to have all used software packages installed. Best regards, Hristo Mihalev

Suggestion To thank Quote Answer

5/26/2014 8:07 AM	Rate (0)
Engr Umair Posts: 50 Rating: (0)	Drive ES PCS 7 Version 8.0 i thinks thats the most advance package ? If i install that package should it work ? That package has all the pacakges and files ?
Engr Umair Posts: 50 Rating: (0)
Suggestion To thank Quote Answer

5/26/2014 8:14 AM	Rate (0)
UMENCHO Diamond Member Joined: 3/21/2006 Last visit: 7/12/2023 Posts: 10221 Rating: (1177)	Engr Umair Drive ES PCS 7 Version 8.0 i thinks thats the most advance package ? If i install that package should it work ? That package has all the pacakges and files ? Drive ES PCS 7 8.0 SP1 is the last version. But are you using PCS7? If not you will need DriveES Basic... As I suggested you eventually to have a confirmation about used software from who did the last changes.
	Last edited by: UMENCHO at: 5/26/2014 8:22 AM
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on