Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

HMI KTP700 Basic link with CPU S7-224XP problem.

Created by: AutoGen_1001023 at: 4/18/2016 10:24 PM (21 Replies)

Rating (2)

Thanks 6

Result pages:: |; 1 | 2 | 3; |

22 Entries

Entries per page: 10 | 20 | all

4/20/2016 3:21 PM	Rate (0)
karthik live Bronze Member Joined: 5/11/2010 Last visit: 11/11/2024 Posts: 90 Rating: (8)	0h0m1s00ms 8193 Seconds bits (8192) + 1Second = 8193

Suggestion To thank Quote Answer

4/20/2016 3:30 PM	Rate (0)
AutoGen_1001023 Advanced Member Joined: 4/15/2015 Last visit: 6/14/2022 Posts: 12 Rating: (0)	I agree with you. You must set the seconds selection bits. (8192 in integer) What is it like Bunch WinCC Flex 2008 Simatic Step 7-300 ... No problem, because the type of WinCC Flex tag "Timer". But I have a bunch of HMI KTP700 Basic <---> CPU S7-224XP. And how to explain S7-224XP (no program change) parameter entered time?

Suggestion To thank Quote Answer

4/20/2016 3:34 PM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	Hello, Please tell us what address of this time value in the HMI and what's its data type. And also tell us the data type defined for the same address in the PLC program.
	Ayman Elotaify
Suggestion To thank Quote Answer

4/20/2016 3:46 PM	Rate (0)
karthik live Bronze Member Joined: 5/11/2010 Last visit: 11/11/2024 Posts: 90 Rating: (8)	S7-200: just linear scaling required in hmi tag properties.

Suggestion To thank Quote Answer

4/20/2016 3:53 PM	Rate (0)
AutoGen_1001023 Advanced Member Joined: 4/15/2015 Last visit: 6/14/2022 Posts: 12 Rating: (0)	Please tell us what address of this time value in the HMI and what's its data type. Tag: Name TTT Address :MW40 Data type: INT And also tell us the data type defined for the same address in the PLC program. Address :MW40

Suggestion To thank Quote Answer

4/20/2016 4:02 PM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 11/11/2024 Posts: 8768 Rating: (1170)	Hello, You want to connect to CPU224XP. Are you sure about MW40? The range MW in CPU224Xp is from 0 to 30 (See online help Step 7 MicroWin) Best regards, Wizard
	Last edited by: Wizard at: 4/20/2016 4:03:24 PM
Suggestion To thank Quote Answer

4/20/2016 4:14 PM	Rate (0)
Ayman Elotaify Platinum Expert Joined: 5/28/2008 Last visit: 11/6/2024 Posts: 4516 Rating: (839)	Wizard Hello, You want to connect to CPU224XP. Are you sure about MW40? The range MW in CPU224Xp is from 0 to 30 (See online help Step 7 MicroWin) Best regards, Wizard Totally agree Please see page 3 of the attached file Attachment S7-200 Quick reference.pdf (376 Downloads)
	Ayman Elotaify
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Wizard

4/20/2016 4:23 PM	Rate (0)
AutoGen_1001023 Advanced Member Joined: 4/15/2015 Last visit: 6/14/2022 Posts: 12 Rating: (0)	Sorry. The project addresses the old panel data start timing with VW40 ..... VW108. For convenience in the S7-315 renamed MW40 ....

Suggestion To thank Quote Answer

4/20/2016 4:27 PM	Rate (0)
AutoGen_1001023 Advanced Member Joined: 4/15/2015 Last visit: 6/14/2022 Posts: 12 Rating: (0)	Debug HMI panel PLC S7-315 because I'm afraid impact on process

Suggestion To thank Quote Answer

4/20/2016 4:46 PM	Rate (0)
Wizard Diamond Member Joined: 4/24/2006 Last visit: 11/11/2024 Posts: 8768 Rating: (1170)	Hello, The number you put in HMI display is the time. But when you use S7-200, the Timer number will give the timebase. So when you put in the number 50. It could be a time 50 x Timebase of used Timer. See online help of Step 7 MicroWin for more information about the timers. Best regards, Wizard

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on