Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

How to use Convert list to S7 data block function in SCOUT

Created by: vorapob at: 9/21/2020 8:21 AM (4 Replies)

Rating (2)

Thanks 0

5 Entries

9/21/2020 8:21 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 10/3/2024 Posts: 1105 Rating: (6)	Dear Expert, How can I use function Convert list to S7 data block in order to automatic generate Data Block. For example I need to create parameter r2090.0 as DB2090 of DO NO.2 in order to monitoring this bit in HMI that connect direct to CU320-2DP. Best Regards, Vorapob Attachment Convert_List_to_S7_data_block.jpg (119 Downloads)
	Best Regards, Vorapob
Suggestion To thank Quote Answer

9/21/2020 8:22 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 10/3/2024 Posts: 1105 Rating: (6)	Attachment R2090.0.jpg (107 Downloads)
	Best Regards, Vorapob
Suggestion To thank Quote Answer

9/21/2020 3:15 PM	Rate (1)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 9/30/2024 Posts: 5909 Rating: (805)	Hello, please see chapter 3.4 https://support.industry.siemens.com/cs/ww/en/view/97550333
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

9/22/2020 10:39 AM	Rate (0)
vorapob Gold Member Joined: 1/17/2013 Last visit: 10/3/2024 Posts: 1105 Rating: (6)	Technology Team Hello, please see chapter 3.4 https://support.industry.siemens.com/cs/ww/en/view/97550333 Dear Technology Team, Thank you for your information but I understand on this chapter 3.4. I ask for how to use this tool Convert list to S7 data block in SCOUT or STARTER ? Best Regards, Vorapob
	Best Regards, Vorapob
Suggestion To thank Quote Answer

9/22/2020 1:33 PM	Rate (1)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 9/30/2024 Posts: 5909 Rating: (805)	Hello, see Onlinehelp. Click the button to convert the parameter set of the expert list or a user-defined parameter/value list to a STEP7 data block. Important note on the exclusive backup of changed parameters (with user-defined expert list) in an S7 data block: It is not recommended that only changed parameters are backed up with a user-defined expert list. There is no guarantee that all parameters still behave identically after reloading a partial backup to the device or to a replacement device. When saving, changed parameter values are only written additively to the parameter values already contained in the device. As a consequence, inconsistencies are possible. No checks or conversions are made with regard to compatibility when the firmware version is changed. Recommendation: Complete backup in S7 data block: Back up all parameters in the "Expert list" view. This ensures that all parameters behave identically after reloading the backup to the device or to a replacement device. Conversion of the parameter list Certain parameters will be automatically filtered out for the conversion of the parameter list to a DB. These are, for example, parameters that are locked for the selection of a list motor (p300, p301), a motor filter (p230) or a PROFIBUS standard telegram (p922). A created user-defined parameter list or value list must be saved before you can convert it into a data block. Complete block is used for the following FB FB PDAT_UD2: Upload / download drive parameters (DS47) FB 42 The block number can be altered. This block cannot be used on some series 300 CPUs on which the SFC24 (TEST_DB) is not installed. In the case of CPUs with MMC memory cards, the section "Data Management in the Loading Memory" must be complied with (FB52 "SHELL_MMC_PDAT_DL"). Calling OBs The block can be incorporated into one of the following OBs: Cyclical task: OB1 Cyclic interrupt OB: e.g. OB32 Features 􀂾 Can be used for all drives which support "Parameter access with DPV1" (DS47) in accordance with "PROFIBUS Profile Drive Technology, V3.1, November 2002" (see Section 7.3 “Formulating parameter jobs (data record 47)) 􀂾 Download/partial download functionality 􀂾 Upload/partial upload functionality 􀂾 The parameter DB structure must comply with the "Structure of parameter job DB" definition ..." (see Subsection 7.4.1.3). 􀂾 The parameter DB should be created by the system via the "Convert parameter set to DB" function in Starter Drive ES. This function can be used for MICROMASTER 4xx and SINAMICS only and generates DS47 jobs.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on