Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Manual transferring of wincc V7.0 project to runtime

Created by: Sz0 at: 8/19/2011 12:05 PM (6 Replies)

Rating (0)

Thanks 0

7 Entries

8/19/2011 12:05 PM	Rate (0)
Sz0 Advanced Member Joined: 3/22/2011 Last visit: 8/15/2023 Posts: 18 Rating: (0)	Dear experts, I have following situation. I have Siemens S315/2DP PLC unit, visualization PC(with WinCC Runtime Advanced) and programmming PC(Step 7, WinCC V7.0. Communication is based on Industrial Ethernet (TCP/IP). IP config is OK, because all devices are seeing each other. The problem is that from my programming PC i cannot download WinCC to visualization PC.I assumed that I need Station Configuration Editor on clients PC, but I cannot install it So I gave up with this and figured out that I can just copy necessary files manually and set them in RT loader because for me, most important is that I can download PLC program to the unit and monitor it, I do need to have permanent connection with clients PC. But I do not have a clue what do I need to copy and how should I set RT loader. Please help I am a newbie in WinCC world. Best regards, Simon

Suggestion To thank Quote Answer

8/19/2011 12:21 PM	Rate (0)
Bizur Posts: 1530 Rating: (59)	Hello Sz0, do you have an integrated project with an engineering station? Please let us know Bizur
Bizur Posts: 1530 Rating: (59)
Suggestion To thank Quote Answer

8/19/2011 1:06 PM	Rate (0)
Sz0 Advanced Member Joined: 3/22/2011 Last visit: 8/15/2023 Posts: 18 Rating: (0)	Yes, project is integrated with station. In Simatic Manager, I have PLC unit (with all peripherials, and CP343-1 Lean with 2 I.E ports), I have Simatic PC station under which I have WinCCApp(under which I have OS(WinCC programme) and IE General, and I do have PG unit as my programming PC. All of them are connected via Ind Ethernet(TCP/IP). Both PCs can communicate with PLC but one PC cannot send anything to the other although if I ping one PC from another then I get response.

Suggestion To thank Quote Answer

8/19/2011 1:14 PM	Rate (0)
Bizur Posts: 1530 Rating: (59)	Hello Sz0, could you please tell me which message you get, if you try to load something? Best regards Bizur
Bizur Posts: 1530 Rating: (59)
Suggestion To thank Quote Answer

8/19/2011 2:28 PM	Rate (0)
Sz0 Advanced Member Joined: 3/22/2011 Last visit: 8/15/2023 Posts: 18 Rating: (0)	First of all in WinCC itself I did not find any button that will transfer program from WinCC to WinCC runtime as it has place in WinCC flex, so I am pressing on entire PC station in Simatic Manager and I am getting msg that connection cannot be established. Anyway can you perhaps know how to copy this program manually and set into runtime? It is not necessary to set this connection between these two PCs but I just need runtime up and running. Thanks in advance for helping me out:)

Suggestion To thank Quote Answer

8/22/2011 3:21 PM	Rate (0)
Wüstenräuber Gold Member Joined: 10/3/2008 Last visit: 9/20/2023 Posts: 946 Rating: (122)	Hi, do you use TIA Portal?

Suggestion To thank Quote Answer

9/21/2011 5:51 PM	Rate (0)
Sz0 Advanced Member Joined: 3/22/2011 Last visit: 8/15/2023 Posts: 18 Rating: (0)	Hello, No, I was usin WinCC 7.0, and after conversation with Siemens Support it appeared that I tried to combine programmes from two different branches - WinCC 7.0 is not using separate runtime programs it has integrated runtime and all I needed was license :) WinCC Runtime Adv is used in Tia portal as far as I know :) Problem solved :) Thx Regards, Simon

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

TIA WinCC Installation Options General

Follow us on