Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Milltronics BW500

Created by: Bekzhan77 at: 7/12/2021 12:20 PM (17 Replies)

Rating (0)

Thanks 2

Result pages:: |; 1 | 2; |

18 Entries

Entries per page: 10 | all

7/12/2021 12:20 PM	Rate (0)
Bekzhan77 Posts: 9 Rating: (0)	Hello everyone. I have a Milltronics BW500 integrator. And there is often an error, sometimes it overestimates, sometimes it underestimates. Can you tell me why this is happening?
Bekzhan77 Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

7/19/2021 1:52 PM	Rate (0)
Siwarexi Gold Expert Joined: 1/4/2007 Last visit: 12/5/2024 Posts: 1153 Rating: (175)	Hello Bekzhan77, You wrote: „And there is often an error, …“!?! Which error occurs? Also, you wrote: „… sometimes it overestimates, sometimes it underestimates.“ What overestimates and underestimates? Best regards Siwarexi

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users aleksPLCSIM

7/22/2021 9:49 AM	Rate (0)
Bekzhan77 Posts: 9 Rating: (0)	Появилась новая проблема, на ленте установлено 4 датчика веса и только 2 датчика веса отображаются на параметре P940. Не показывает тензодатчики, подключенные к клеммам 6/7 и 8/9. Фото s и видео показаны ниже: [snip] https://radikal.ru/video/gpBuswWT7e4 С уважением Attachment Images.zip (951 Downloads)
Bekzhan77 Posts: 9 Rating: (0)	Last edited by: Jen_Moderator at: 07/22/2021 11:12:03 Removed links and added images as an attachment.
Suggestion To thank Quote Answer

7/22/2021 11:14 AM	Rate (0)
Jen_Moderator Diamond Member Joined: 6/19/2017 Last visit: 9/6/2024 Posts: 8175 Rating: (173)	Hi Bekzhan77, Please try to discuss your question in English language. This is an international community and we try to focus on one language. Posting in English will help you to get more response to your question. This is the translation of your question: Bekzhan77 There is a new problem, 4 weight sensors are installed on the belt and only 2 weight sensors are displayed in parameter P940. The load cells connected to terminals 6/7 and 8/9 do not show. Photo s and video are shown below: [snip] https://radikal.ru/video/gpBuswWT7e4 Regards Attachment Images.zip(0 Downloads) Regards, Jen_Moderator

Suggestion To thank Quote Answer

7/22/2021 1:28 PM	Rate (0)
Siwarexi Gold Expert Joined: 1/4/2007 Last visit: 12/5/2024 Posts: 1153 Rating: (175)	Hello Bekzhan77, That’s strange! Can you give me from your BW500 the following information, please: 1. the order number (= 7MH…) 2. the Serial number of your BW500 I would like to check your BW500. Best regards Siwarexi

Suggestion To thank Quote Answer

7/23/2021 9:12 AM	Rate (0)
Bekzhan77 Posts: 9 Rating: (0)	Hi, yes of course. 1. 7MH71522AA022BA 2. PBD/F9030071
Bekzhan77 Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

7/23/2021 3:23 PM	Rate (0)
Siwarexi Gold Expert Joined: 1/4/2007 Last visit: 12/5/2024 Posts: 1153 Rating: (175)	Hello Bekzhan77, What can you see in P900? Would it be possible for you to reset the BW500 with P999 to the factory settings? Pay attention, that afterwards, you have to do a new calibration! Another solution would be, that you check the load cells C and D manually with a voltmeter on the PCB. Best regards Siwarexi

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Bekzhan77

8/5/2021 9:04 AM	Rate (0)
Siwarexi Gold Expert Joined: 1/4/2007 Last visit: 12/5/2024 Posts: 1153 Rating: (175)	Hello Bekzhan77, What can you see in P900? Parameter P900 is the firmware of your BW500. Best regards Siwarexi

Suggestion To thank Quote Answer

8/19/2021 10:54 AM	Rate (0)
Bekzhan77 Posts: 9 Rating: (0)	Thank you, I'll check it out this week
Bekzhan77 Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

9/13/2021 1:02 PM	Rate (0)
Bekzhan77 Posts: 9 Rating: (0)	Hi, I manually checked the load sensors C and D. They work, the signals are sent to the voltmeter. Now I want to do a factory reset, but I don't have any calibration weights. Is it possible to do this without calibration scales? With respect
Bekzhan77 Posts: 9 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on