Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

( need help)siemens 810 t ga2

Created by: egypt at: 9/29/2009 8:26 PM (7 Replies)

Rating (1)

Thanks 1

8 Entries

9/29/2009 8:26 PM	Rate (0)
egypt Posts: 10 Rating: (0)	Dear sir. ihave cnc lathe with siemens 810 t ga2 machine have (c axis)drivien tools with resiliotian 2.5 deg but in the screen iam noot see the c axis read ineed to know how the the drivien tool working in this control &inee smoll program for test c axis &drivien tool pls help me thank you ahmed
egypt Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

9/29/2009 9:04 PM	Rate (0)
audy Posts: 71 Rating: (2)	Dear Ahmed, you said that C axis working but not displayed so, did you tried to move it and you found it is working ok? And you working with it which method you used (jog mode or automatic)? Thanks so much for your posting. eyad
audy Posts: 71 Rating: (2)
Suggestion To thank Quote Answer

9/29/2009 9:17 PM	Rate (0)
egypt Posts: 10 Rating: (0)	only thank you for reply idont know how c axis working in the machine screen isee only x axis &z axis not see c axis &machine have c axis &driven tools
egypt Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

9/29/2009 9:37 PM	Rate (0)
audy Posts: 71 Rating: (2)	Dear Sir, You have Drive C phisycally installed but I think it is not actually integrated into the system, because you have to see it inthe screen also it must go to reference point like X,Z axes because it is synchronous motor not like spindle (asynchronous), you should back to the agency that you bought the machine from. Thanks so much eyad alim
audy Posts: 71 Rating: (2)
Suggestion To thank Quote Answer

9/30/2009 7:39 AM	Rate (0)
jove Regular Member Joined: 11/7/2005 Last visit: 3/18/2023 Posts: 12 Rating: (1)	Dear Sir Ithink that is TRANSMIT Option you are using in your machine, you can refer to opterating and programming manual. face machining with TRANSMIT, spindle as c-axis, the programming axes are X, Y, Z, (in here, X,Y are fictitious axis), so c-axis not need to display. best regards jove
	Last edited by: jove at: 9/30/2009 7:42 AM
Suggestion To thank Quote Answer

10/2/2009 3:38 PM	Rate (1)
Pee Ell Sea Posts: 672 Rating: (56)	HI, Reolution 2.5 degrees sounds like budget option to me. It is possible there is no c axis but that the spindle stops at 2.5 degree positions and there is a clamping plate or shot bolt or similar to hold the spindle in position. The driven tooling can then be used to drill holes or mill keyways but not contouring moves. There is probably a cycle to position the spindle or an m code to clamp it up. Have a look at the spindle mechanics of the machine and see what is fitted. If you have further questions please post again.
Pee Ell Sea Posts: 672 Rating: (56)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Aviator_747

7/2/2010 2:07 PM	Rate (0)
egypt Posts: 10 Rating: (0)	Dear sir thank you for attention you are right mr pee ell sea thank you but the problem i don't know g code for driven tool i have driven tool station but i dont know g code or m code for driven tool & g or m code for chuck brack to indexing thank you Ahmed
egypt Posts: 10 Rating: (0)
Suggestion To thank Quote Answer

12/14/2010 3:43 PM	Rate (0)
iamnayak Advanced Member Joined: 11/10/2010 Last visit: 1/15/2023 Posts: 15 Rating: (3)	I can solve your problem
	Last edited by: O_Moderator at: 12/14/2010 7:41 PM contact data deleted
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on