Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Need help with ET 200SP

Created by: Kaltunas at: 7/23/2013 8:21 AM (9 Replies)

Rating (7)

Thanks 10

10 Entries

7/23/2013 8:21 AM	Rate (0)
Kaltunas Posts: 10 Rating: (4)	Configuration: S7-1200 (6ES7 214-1AG31-0XB0) ET 200SP (6ES7155-6AA00-0BN0) (Connected to the controller via profinet) 2 x DI 16x24VDC ST Digital input modules (6ES7131-6BH00-0BA0) When I add one of the modules everything is working fine, but after adding two or more, the following errors occur: Fault: Hardware component removed or missing - \|> HW_ID= 271 CPU error: New I/O access error during process image update /n input 2 (2 Bytes) will temporarily not be updated as part of the updating of PIP 0 \|> \|> HW_ID= 279 - Object management system CPU error: New I/O access error during process image update /n input 4 (2 Bytes) will temporarily not be updated as part of the updating of PIP 0 \|> \|> HW_ID= 280 - Object management system Fault: Hardware component not available due to a parameter assignment error - \|> HW_ID= 280 Modules aren't faulty, tried to replace one of them to digital output module, but the outcome is the same.
Kaltunas Posts: 10 Rating: (4)
Suggestion To thank Quote Answer

7/23/2013 12:25 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 6/2/2023 Posts: 8587 Rating: (1127)	Hello Kaltunas, Are you using the "server module" at the end (right) (Small module to terminate bus) Best regards, Wizard

Suggestion To thank Quote Answer

7/23/2013 12:46 PM	Rate (0)
Kaltunas Posts: 10 Rating: (4)	Hello Wizard, Yes, I'm using the server module. Finally solved the problem, the thread can be closed or deleted. Thank you for your efforts in trying to help.
Kaltunas Posts: 10 Rating: (4)	Last edited by: Kaltunas at: 7/23/2013 12:46 PM
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Wizard

7/23/2013 1:19 PM	Rate (1)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 6/2/2023 Posts: 8587 Rating: (1127)	Hi Kaltunas, Great you solved the problem Perhaps you can share with us, how you solved the problem. it might help others. Best regards, Wizard

Suggestion To thank Quote Answer

7/23/2013 1:37 PM	Rate (4)
Kaltunas Posts: 10 Rating: (4)	I found out that there are two kind of base units (the light one and the darker one). When I set the configuration on tia portal, the second input module by default was set as the darker one, while both of the base units were light kind... Quite a stupid mistake.
Kaltunas Posts: 10 Rating: (4)	Last edited by: Kaltunas at: 7/23/2013 1:38 PM
Suggestion To thank Quote Answer
This contribution was helpful to 7 thankful Users Wizard O_Moderator Stavros Ch. RC23 burroaktyson npatti Eshita11

5/22/2014 2:20 PM	Rate (0)
imorales2 Regular Member Joined: 5/20/2014 Last visit: 11/25/2022 Posts: 6 Rating: (0)	could you post image ?? i dont understand dark and ligh :S

Suggestion To thank Quote Answer

5/23/2014 8:48 AM	Rate (2)
Pittiplatsch Posts: 1368 Rating: (126)	Hello imorales2, at ET200SP,There are different BaseUnit versions: BaseUnits (with light terminal box) for opening a potential group: BU..D BaseUnits (with dark terminal box) for conducting the potential group: BU..B In the TIAconfiguration of ET200SP, you have to choose the usedbaseunit and the information, if the baseunit opens a new potential group or not. Is it clear now?
Pittiplatsch Posts: 1368 Rating: (126)
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users rluqueb

5/27/2014 9:11 PM
SMHZ Bronze Member Joined: 10/19/2012 Last visit: 4/17/2022 Posts: 315 Rating: (9)	Good that you were able to trace the problem by yourself. .

Suggestion Quote Answer

6/4/2014 3:01 PM	Rate (0)
Stavros Ch. Posts: 6 Rating: (0)	Kaltunas I found out that there are two kind of base units (the light one and the darker one). When I set the configuration on tia portal, the second input module by default was set as the darker one, while both of the base units were light kind... Quite a stupid mistake. Thank you. I had the same problem and I was stuck for a day.
Stavros Ch. Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

6/14/2021 10:59 AM	Rate (0)
WojciechSulek Member Joined: 2/4/2021 Last visit: 6/6/2022 Posts: 2 Rating: (1)	Thanks for the previous posts. Helped me to get going Dark/light modules explained here: https://vimeo.com/562678756

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users LuisSilaNano

|

Share this page:

Share this page on...

Follow us on