Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

NEED TO CONFIGURE POWER MODULE PM240-2 OF SINAMICS G120 WITH CONTROL UNIT CU250S-2 PROFINET IN TIA POARTAL

Created by: P@S at: 2/23/2017 9:46 PM (6 Replies)

Rating (1)

Thanks 0

7 Entries

2/23/2017 9:46 PM	Rate (0)
P@S Posts: 10 Rating: (1)	HI ALL, IN TIA PORTAL SOFTWARE I NEED TO COMMUNICATE , POWER MODULE PM240-2 OF SINAMICS G120 RATINGS:-4KW INPUT VOLTAGE:- 3 PH,380-480VAC(6SL3210-1PE21-4UL0) and POWER MODULE PM240-2 OF SINAMICS G120 RATINGS:-2.2KW INPUT VOLTAGE:- 3 PH,380-480VAC(6SL3210-1PE18-0UL1) AND CONTROL UNIT CU250S-2 PROFINET (6SL3246-0BA22-1FA0) WITH THE IM151-8 2 PN/DP......BUT WHEN I START TO CONFIGURE THE HARDWARE IN SOFTWARE I DID NOT FOUND THE POWER MODULE AS MENTION ABOVE . SO PLEASE SUGGEST THE REQUIRED CONFIGURATION. HOW CAN DO THIS USING TIA PORTAL. I WANT GO ONLINE FOR G120 THROUGH TIA SOFTWARE ONLY. PLEASE DO THE NEEDFULL BECOUSE I AM ON SITE PRESENTLY
P@S Posts: 10 Rating: (1)
Suggestion To thank Quote Answer

2/24/2017 6:42 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	Hello, have you installed Startdrive? Regards Christoph

Suggestion To thank Quote Answer

5/10/2017 12:05 PM	Rate (0)
dzozee Posts: 7 Rating: (0)	Did you found any solution?
dzozee Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

5/10/2017 12:14 PM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	dzozee Did you found any solution? no feedback given. Do you have a similar or the same problem?

Suggestion To thank Quote Answer

5/10/2017 12:20 PM	Rate (0)
dzozee Posts: 7 Rating: (0)	ChristophD dzozee Did you found any solution? no feedback given. Do you have a similar or the same problem? exactly, I can't find Article number (6SL3210-1PE26-0AL0) when I'm adding new device in TIA PORTAL v14 update 2.
dzozee Posts: 7 Rating: (0)
Suggestion To thank Quote Answer

5/10/2017 12:27 PM	Rate (1)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 12/1/2023 Posts: 21949 Rating: (2927)	Hello, do you have installed Startdrive? Which Control Unit you have created or which drive Type? The 6SL3210-1PE26-0AL0 is only the Powermodule, before you can select the module you must create the Control unit, then open the device configuration and here you can insert the powermodule. Regards Christoph

Suggestion To thank Quote Answer

10/22/2018 6:46 AM	Rate (0)
RaulSuarez Posts: 1 Rating: (0)	It is Very important to check the software version of the control unit. I recommend you to connect to the control unit and then in Project view and with online/Accessible devices option you make a diagnostic and the version is shown
RaulSuarez Posts: 1 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_G

Follow us on