Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

PLC program check online on 840D controller

Created by: sagar k. at: 10/23/2012 2:53 PM (6 Replies)

Rating (0)

Thanks 1

7 Entries

10/23/2012 2:53 PM	Rate (0)
sagar k. Posts: 25 Rating: (0)	Dear sir 1) How to go windows mode in 840D controller. 2) How i can check online program in 840D controller. Thanks & regards Sagar K
sagar k. Posts: 25 Rating: (0)
Suggestion To thank Quote Answer

10/25/2012 12:37 PM	Rate (0)
PISCEAN 2010 Diamond Expert Joined: 4/23/2010 Last visit: 3/21/2023 Posts: 8022 Rating: (855)	sagar k. Dear sir 1) How to go windows mode in 840D controller. Sagar K When control is Switched on you find a Sinumerik 840D power line screen displayed on this screen below right side bios version displayed for ex:(V08.02.00.06). Immediately press no 3 on the operator panel. > Now you find Service Desktop Screen in this enter user name:AUDUSERand password:SUNRISE > You will find Windows screen getting open. sagar k. Dear sir 2) How i can check online program in 840D controller. Thanks & regards Sagar K You need PG/PC with step 7 & MPI cable. Then on PG/PC you can monitor/ edit PLC. On HMI directly you cannot go on line.Hope this helps.DEEP.

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users samiraj

10/25/2012 7:46 PM	Rate (0)
sagar k. Posts: 25 Rating: (0)	DearPISCEAN 2010 Thanks. We have 840D controller with PCU 50, I think may it is possible to see PLC program in that configration. So how to check ladder there. Thanks Sagar K.
sagar k. Posts: 25 Rating: (0)
Suggestion To thank Quote Answer

10/26/2012 6:45 AM	Rate (0)
Nanu_333 Bronze Member Joined: 5/19/2011 Last visit: 1/20/2023 Posts: 196 Rating: (5)	Dear Sagar, Which PCU version you have means PCU 50.1, .2, .3. For watching ladder on HMI, You have to take & install STEP7 package for your PCU if not installed. Regards, Chetan

Suggestion To thank Quote Answer

10/26/2012 6:45 AM	Rate (0)
List Posts: 664 Rating: (17)	Hai sagar k., With your thread i understood that you have to see the ladder in OP. With my knowledge every 840D+PCU50 will not give you the option to see and edit ladder in OP.with respect to the version of controller, having the option to see and edit the Ladder in OP. In your controller if there is an option to see the ladder, you can see the ladder in online, Better try for SIMATIC MANAGER and upload the PLC backup and you can go for online and editing.. Thanks&Regards, Raj
List Posts: 664 Rating: (17)
Suggestion To thank Quote Answer

2/27/2013 4:40 PM	Rate (0)
samiraj Experienced Member Joined: 10/13/2012 Last visit: 2/25/2023 Posts: 79 Rating: (0)	dear friends i couln't enter windows xp desktop mode , by press "3" key , regrads samiraj

Suggestion To thank Quote Answer

2/28/2013 6:13 AM	Rate (0)
Ekalavya Posts: 2964 Rating: (473)	samiraj dear friends i couln't enter windows xp desktop mode , by press "3" key , regrads samiraj Hello, May be your having base software version this07.xx.xx.xx. Please check i replied your previous post.... Regards, Prakash
Ekalavya Posts: 2964 Rating: (473)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on