Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

pls help me for sinamics v20 Jog parameters programming

Created by: AutoGen_484821 at: 4/9/2017 4:28 PM (6 Replies)

Rating (0)

Thanks 0

7 Entries

4/9/2017 4:28 PM	Rate (0)
AutoGen_484821 Posts: 6 Rating: (0)	pls help me for sinamics v20 Jog parameters programming . i am not getting P0840 PARAMETER
AutoGen_484821 Posts: 6 Rating: (0)	Last edited by: AutoGen_484821 at: 4/9/2017 4:30:05 PM
Suggestion To thank Quote Answer

4/10/2017 10:21 AM	Rate (0)
MichalWZ Silver Member Joined: 3/31/2015 Last visit: 11/5/2024 Posts: 175 Rating: (16)	P0840 requires P0003 = 3

Suggestion To thank Quote Answer

4/12/2017 5:55 AM	Rate (0)
AutoGen_484821 Posts: 6 Rating: (0)	Sir these are my parameters , but my jog or inch not working pls guide me. p0003 - 3 p0700- 2 p1000 - 2 P0840-2817.0 P0701-99 P0702-99 P2816- IN00-722.0 IN01 -722.1 P2801-1 P1080 -50.0 P1082- 52.0 P1120- 3 P1121-2 P0971-1 MY CONNECTION MACRO TYPE TERMINAL CnOO4 ------ sir please help to run my motor in inch/ Jog mode, may i change Macro ? now my motor working well in normal Running. pls help me to run in both jog and normal . thanks sir, madhu
AutoGen_484821 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

4/13/2017 6:06 AM	Rate (0)
AutoGen_484821 Posts: 6 Rating: (0)	AutoGen_484821 Sir these are my parameters , but my jog or inch not working pls guide me. p0003 - 3 p0700- 2 p1000 - 2 P0840-2817.0 P0701-99 P0702-99 P2816- IN00-722.0 IN01 -722.1 P2801-1 P1080 -50.0 P1082- 52.0 P1120- 3 P1121-2 P0971-1 MY CONNECTION MACRO TYPE TERMINAL CnOO4 ------ sir please help to run my motor in inch/ Jog mode, may i change Macro ? now my motor working well in normal Running. pls help me to run in both jog and normal . thanks sir, madhu
AutoGen_484821 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

4/13/2017 6:07 AM	Rate (0)
AutoGen_484821 Posts: 6 Rating: (0)	Pls help me for Jog mode to connect from jog push button to DI2 thks Sir
AutoGen_484821 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

4/13/2017 9:00 AM	Rate (0)
MichalWZ Silver Member Joined: 3/31/2015 Last visit: 11/5/2024 Posts: 175 Rating: (16)	P1055 is the enable for Jog Right. If you set P1055 = r0722.X, where X is the desired DI it should work. Please see the OPI for details or atleast describe your desired control in more detail. All I understand is that you want to JOG, but what about the normal operation. Why is there OR FFB used? Is the min freq of 50 and max freq of 52 what you wanted to achieve? Why did you choose Cn004?

Suggestion To thank Quote Answer

4/14/2017 11:29 AM	Rate (0)
AutoGen_484821 Posts: 6 Rating: (0)	Dear Sir good evening, Thanks for your kind answer, My normal mode DI 1 working ok. min and max frequency also 50 and 52 as told you. I choosen cn004 just for trial as for my connection diagram. I want Normal run in DI1 and Jog in DI 2 of PNP type connection. I am not using pot for speed control. just using push buttons to run as terminal mode one for normal run and other for Jog and stop button. I am sending my electrical connecting drawing also, pls help me run in Normal as well As Jog mode. now narmal working ok.
AutoGen_484821 Posts: 6 Rating: (0)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_V

Follow us on