Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

Power Supply to 840D NCU

Created by: dabr at: 6/7/2009 11:25 AM (7 Replies)

Rating (0)

Thanks 0

8 Entries

6/7/2009 11:25 AM	Rate (0)
dabr Posts: 5 Rating: (0)	Hello all, for testing reason I have to supply 840D NCU at my office desk. I have E/R module but I cannot have 3phases 400VAC at my desk. Only normal 220VAC, Phase+Neutral. There's some possibility to get somehow power to NCU by X172 connector? Power to electronics is very complicate to get by "normal" power supply (57VDC, 20Khz...). Thanks in advance
dabr Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

6/7/2009 11:40 AM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Hi Just as thought You have an ER-Modul ! (With Power for Power-Module) UEB-Unit should make this possible?
	Karl
Suggestion To thank Quote Answer

6/7/2009 1:53 PM	Rate (0)
dabr Posts: 5 Rating: (0)	Hello, As I wrote, I do not have possibility to get 3phases 400VAC at desk. E/R module I have (6SN1145-1BA01-0BA1) couldn't work with 220VAC 1phase line. What is UEB-Unit? Never heard or maybe I need explanation... thanks
dabr Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

6/7/2009 4:43 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Hi >As I wrote, I do not have possibility to get 3phases 400VAC at desk. O.K. >E/R module I have (6SN1145-1BA01-0BA1) couldn't work with 220VAC 1phase line. It is right. >What is UEB-Unit? Never heard or maybe I need explanation... UEB-Modul or UE-Modul. When you need more Powermoduls for "check for error" you need an "Control"-Unit. This Part have standalone 5V, -15V, +15V, +24V in it. But i have check the Diagramm --> You need 3 Phase 400V to. Sorry.
	Karl
Suggestion To thank Quote Answer

6/7/2009 6:43 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Hi How urgent is this ? You can take a MM420 (Micromaster) 1 Phase in 220Volt --> 3 Phase out 400 Volt. Parameter for OUTPUT on 60 Hz. On E/R-Modul you takeonly the "Energy" ontop (Only 3 Phase, no Power-Input) Do you know what i mean ? Only Power on Conektor 2U1, "V1, 2W1 --> Onlyfor intern Voltage -15, +15, +24 . . . I think, that should be work.
	Karl
Suggestion To thank Quote Answer

6/8/2009 12:18 AM	Rate (0)
dabr Posts: 5 Rating: (0)	Hello, Yes I know what you mean. Just I need power to X181 connector for the Electronics Power Supply (looking at infeed module diagram sounds like module stay off but will give power to Device Bus Interface). But how about that Inverter? That MM420 is a normal 3 phases motor inverter. Are you sure that I can get 3 phases starting form 1? Thanks
dabr Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

6/8/2009 12:31 AM	Rate (0)
dabr Posts: 5 Rating: (0)	Ok Karl, I've download the User Manual of that inverter and now I know how to... Thanks for all support. Regards
dabr Posts: 5 Rating: (0)
Suggestion To thank Quote Answer

6/8/2009 8:47 PM	Rate (0)
Gebhardt Karl Platinum Expert Joined: 7/16/2006 Last visit: 1/2/2024 Posts: 1502 Rating: (176)	Hi The Forum enyoy when we can help. I you want, you can "rate" people in this Forum. Bye bye
	Karl
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on