Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

problem regarding communication of S7-414H with S7-200 Network

Created by: Rafaqatali at: 5/23/2010 8:07 AM (2 Replies)

Rating (0)

Thanks 0

3 Entries

5/23/2010 8:07 AM	Rate (0)
Rafaqatali Posts: 2 Rating: (0)	I am facing some problem regarding communication of S7-414H with S7-200 Network. Following Indications are coming on Siemes MODULES. 1)Reclaimer (S7-200) ET200M1 BF1 Red Constant BF2 Red Constant On Yellow Constant 2)Reclaimer (S7-200) ET200M2 BF1 Red Constant BF2 Red Constant On Yellow Constant 3)Reclaimer (S7-200) Y Link On Yellow Constant 4)Tripper (S7-200) ET200M1 BF1 Red Constant BF2 Red Constant On Yellow Constant 5)Tripper (S7-200) ET200M2 BF1 Red Constant BF2 Red Constant On Yellow Constant 6)Tripper (S7-200) Y Link On Yellow Constant 7)Remote IO Panel ET200M1 BF1 Red Constant On Yellow Constant 8)Remote IO Panel Panel ET200M2 ACT Yellow Constant On Yellow Constant Kindly suggest some solutions. We have tried every possibility but all in vain. Splitted from profibus network communication. Attachment DCS Mesages.pdf (102 Downloads)
Rafaqatali Posts: 2 Rating: (0)	Last edited by: O_Moderator at: 5/25/2010 8:38 AM new subject after splitting Last edited by: Rafaqatali at: 5/23/2010 8:15 AM
Suggestion To thank Quote Answer

5/23/2010 8:16 AM	Rate (0)
Rafaqatali Posts: 2 Rating: (0)	Rafaqatali I am facing some problem regarding communication of S7-414H with S7-200 Network. Following Indications are coming on Siemes MODULES. 1)Reclaimer (S7-200) ET200M1 BF1 Red Constant BF2 Red Constant On Yellow Constant 2)Reclaimer (S7-200) ET200M2 BF1 Red Constant BF2 Red Constant On Yellow Constant 3)Reclaimer (S7-200) Y Link On Yellow Constant 4)Tripper (S7-200) ET200M1 BF1 Red Constant BF2 Red Constant On Yellow Constant 5)Tripper (S7-200) ET200M2 BF1 Red Constant BF2 Red Constant On Yellow Constant 6)Tripper (S7-200) Y Link On Yellow Constant 7)Remote IO Panel ET200M1 BF1 Red Constant On Yellow Constant 8)Remote IO Panel Panel ET200M2 ACT Yellow Constant On Yellow Constant Kindly suggest some solutions. We have tried every possibility but all in vain.
Rafaqatali Posts: 2 Rating: (0)
Suggestion To thank Quote Answer

5/23/2010 6:43 PM	Rate (0)
Hulzhex Gold Member Joined: 8/25/2005 Last visit: 10/5/2024 Posts: 1162 Rating: (111)	Hello Rafaqatali, think it would be much more effectiv to start a new thread than to publish an new question within an existing thread. I think non of your slaves go into data transfer with the master. Reading the diagnostic you published the master try to configure the slave but there is no response. Have you checked the PROFIBUS plugs? Have you checked the adresses at the slaves? Maybe you could have a look at the at the profibus with your PG to check if the slaves are available? Or connect only one slave with the master Good luck Sabine

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on