Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

PWM Testing

Created by: Nelliyan randy at: 4/2/2013 8:58 AM (4 Replies)

Rating (0)

Thanks 0

5 Entries

4/2/2013 8:58 AM	Rate (0)
Nelliyan randy Posts: 461 Rating: (29)	Hi, I was just testing the PWM concept in cpu 1212 c using v11 , i assigned the parameters in a way that was described in that sample program. I downloaded the code & its working i.e the op Q0.0 was on while i trigger the enable , but no voltage was readed across the Q0.0 terminal while i use the MultiMeter to read voltage. But 24 v was read across another D.O i assigned for testing. I read the voltage by placing the MM terminal in - 24 v & Q0.0 terminal [is it right] I dint understand what i am missing , also some pls give me some explanation regarding the parameter assignment that i din't understand with manual. Thanks & Regards, Nelliyan.G
Nelliyan randy Posts: 461 Rating: (29)
Suggestion To thank Quote Answer

4/2/2013 2:37 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/6/2023 Posts: 13982 Rating: (2282)	Nelliyan randy Hi, I was just testing the PWM concept in cpu 1212 c using v11 , i assigned the parameters in a way that was described in that sample program. I downloaded the code & its working i.e the op Q0.0 was on while i trigger the enable , but no voltage was readed across the Q0.0 terminal while i use the MultiMeter to read voltage. But 24 v was read across another D.O i assigned for testing. I read the voltage by placing the MM terminal in - 24 v & Q0.0 terminal [is it right] I dint understand what i am missing , also some pls give me some explanation regarding the parameter assignment that i din't understand with manual. Thanks & Regards, Nelliyan.G Which version of the S7-1212 are you using? DC/DC/DC? What address are you modifying to set the PWM output? To see a PWM signal, you should probably use an oscilloscope.
	science guy
Suggestion To thank Quote Answer

4/3/2013 10:19 AM	Rate (0)
Nelliyan randy Posts: 461 Rating: (29)	I attached my PWM configuration Version 2.1 , 1212c DC/DC/DC Regards, Nelliyan.G Attachment My PWM config.pdf (198 Downloads)
Nelliyan randy Posts: 461 Rating: (29)
Suggestion To thank Quote Answer

4/3/2013 2:56 PM	Rate (0)
0_Einstein Diamond Expert Joined: 7/7/2010 Last visit: 12/6/2023 Posts: 13982 Rating: (2282)	Can you post a screenshot of your CTRL_PWM block and surrounding logic to enable it, maybe while it is online with the PLC so the current values are visible? See attached image showing the system defined constant HW_PWM datatype tag rather than the absolute address of the HW_PWM. Attachment C:\TEMP\CTRL_PWM_showing_HW_PWM_tag.jpg (273 Downloads)
	Last edited by: huggy_d1 at: 4/3/2013 3:14 PM Last edited by: huggy_d1 at: 4/3/2013 3:12 PM added screenshot science guy
Suggestion To thank Quote Answer

4/4/2013 6:38 AM	Rate (0)
Nelliyan randy Posts: 461 Rating: (29)	Hi , I attached the imag for ur view I think i dont know how to check the op because when i trigger the enable bit m0.0 respective q0.0 was triggered . Pls tell me how to use an oscilloscope for checking it in plc i havent used it before Thanks & Regards, Nelliyan.G Attachment PWM 1.jpg (272 Downloads)
Nelliyan randy Posts: 461 Rating: (29)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on