Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

r46.0 OFF1,enable missing

Created by: khangtd46 at: 1/17/2019 6:22 AM (9 Replies)

Rating (0)

Thanks 2

10 Entries

1/17/2019 6:22 AM	Rate (0)
khangtd46 Bronze Member Joined: 10/27/2017 Last visit: 1/12/2023 Posts: 59 Rating: (0)	Hello experts, i tried to test my sinamics power modul and a CU320. I connected them to starter and everything is okay, in the alarm tab, it said OK. then i tried to run the motor using the control panel. However, i cant, and the message is "Switch on disable active". i checked the parameter p9 = 0, p10 = 1, r46.0 = Yes. i tried to download P840 = 1 to the drive but it still remains p840 = 0. Can someone help me figure out what is wrong? Thank you

Suggestion To thank Quote Answer

1/17/2019 6:35 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 2/1/2023 Posts: 21216 Rating: (2797)	Hello, which power module? which values have r2 and r70? any screen available ? Regards Christoph

Suggestion To thank Quote Answer

1/17/2019 6:40 AM	Rate (0)
khangtd46 Bronze Member Joined: 10/27/2017 Last visit: 1/12/2023 Posts: 59 Rating: (0)	power module: 6SL3310-1TE32-1AA0. r2 = 10. the machine is off now so i cannot check r70. i will give you the screenshot as soon as possible

Suggestion To thank Quote Answer

1/17/2019 7:58 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 1/31/2023 Posts: 5410 Rating: (729)	Hello, p10 = 1 on the axis means that quick commissioning is still pending. Finish quick commissioning first. To download p840 with a static 1 doesn`t enable the drive. Parameter p840 is triggered by a positive edge of the signal connected to p840. So I would recommend using the control panel of STARTER in the first place to check if the motor is running ok. Please use the online help of STARTER to get more information about the single parameters and their corresponding settings. There you can find the information that r2 = 10 indicates that you have to set p1142 enable setpoint to 1.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer

1/17/2019 8:04 AM	Rate (0)
khangtd46 Bronze Member Joined: 10/27/2017 Last visit: 1/12/2023 Posts: 59 Rating: (0)	Attachment z1245153182195_f92527657ab18ee437c73e48b7becb01.jpg (249 Downloads)

Suggestion To thank Quote Answer

1/17/2019 8:06 AM	Rate (0)
ChristophD Grandmaster-Expert Joined: 5/12/2006 Last visit: 2/1/2023 Posts: 21216 Rating: (2797)	Hello, check the fault tab (blue colored) which fault is comming up if you change P10 from 1 to 0. Regards Christoph

Suggestion To thank Quote Answer

1/17/2019 10:17 AM	Rate (0)
khangtd46 Bronze Member Joined: 10/27/2017 Last visit: 1/12/2023 Posts: 59 Rating: (0)	Thank you for your help. I am able to use the green button however, the motor does not run. i use a non-siemens motor to do the test, the motor specification is 0.37kW, 380 rated voltage, .1.13 rated current, 0.75 cos phi. When i set the RPM to 200, the output voltage is just about 30V. Do i need a encoder to make the motor run?

Suggestion To thank Quote Answer

1/17/2019 1:13 PM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 1/31/2023 Posts: 5410 Rating: (729)	Hello, you mentioned that you are using 6SL3310-1TE32-1AA0 power module with 210A. So I think it make no sense to test this drive with a 1.13A motor, especially in close loop. If you want to test the drive I would use v/f mode. There you don`t need a motor on the output but you can operate the drive.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users khangtd46

1/21/2019 7:59 AM	Rate (0)
khangtd46 Bronze Member Joined: 10/27/2017 Last visit: 1/12/2023 Posts: 59 Rating: (0)	Hello, i chose v/f with linear characteristic for my drive. However, when i use control panel to run the drive, the drive stops with the fault wrong motor identification, F07990, r949 = 10. So if i want to do a v/f test without motor, i have to delete the motor in the software? is it correct, and how to do so? Thank you

Suggestion To thank Quote Answer

1/21/2019 8:09 AM	Rate (0)
Technology Team Platinum Expert Joined: 10/11/2006 Last visit: 1/31/2023 Posts: 5410 Rating: (729)	Hello, in your case the motor identification is selected. This will not work without motor of course. So disable the identification in p1910 and try again.
	With best regards, Technology Team Application consulting and pre sales support for SINAMICS, SIMATIC Technology, SIMOTION, SIMOTICS and MOTION CONNECT
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users khangtd46

|

Share this page:

Share this page on...

Related topics by keywords:

SINAMICS_S

Follow us on