S120 fw V5_2_SP3_HF1 and TIA Portal V15.1 Update 4

Dear all,

We have updated a S120 to the fw SINAMICS_S120_FW_V5_2_SP3_HF1.zip

S120: *Control Unit 6SL3040-1MA01-0AA0

          *Double Motor Module 6SL3120-2TE21-0AD0 

We installed this fw in order to identify the 1FK2105-6AF00-0SB0 SIMOTICS S-1FK2 HD servomotor.

Unfortunately, we are not able to upload the S-120 from the device to the project: Tia Portal crashes or shows the message 

   "An upload is not possible with the current StartDrive Version The firmware version of the device is not supported by the current StartDrive Version "

If I try to insert a S120 version 5.2 on the project and then upload "only software" I get: 

   "An upload is not possible due to incompatible configuration Target Drive unit_1 in the offline project differs form the target in the online project"

Installed Software:
* Tia Portal Version V15.1 Update 4

* Startdrive advanced update 3

* SINAMICS Startdrive G130, G150, S120, S150, SINAMICS MV, S210 Version V15.1 Update3

* Step 7 Proffesional Version V15.1 Update 4

* STEP 7 Safety Version V15.1 

What can we do?

How to integrate that S120 on a TIA 15.1? 

Sounds like 3 solutions are available, but not necessarily possible:

1. Update Startdrive to allow S120 FW 5.2.3.1
2. Return S120 firmware to highest level startdrive supports
3. Install latest Sinamics Starter software and integrate with S120 FW 5.2.3.1 using same telegram as configured in startdrive.  Update TIA Portal project so it can communicate with the drive.

If you are lucky, you can leave the startdrive configuration in place, but just not upload / download via TIA Portal.  Many of the startdrive integrations may still work, like parameter access, control panel and other commissioning tools.  At least that has been my experience.

af_tds

Dear all,

We have updated a S120 to the fw SINAMICS_S120_FW_V5_2_SP3_HF1.zip

S120: *Control Unit 6SL3040-1MA01-0AA0

          *Double Motor Module 6SL3120-2TE21-0AD0 

We installed this fw in order to identify the 1FK2105-6AF00-0SB0 SIMOTICS S-1FK2 HD servomotor.

Unfortunately, we are not able to upload the S-120 from the device to the project: Tia Portal crashes or shows the message 

   "An upload is not possible with the current StartDrive Version The firmware version of the device is not supported by the current StartDrive Version "

If I try to insert a S120 version 5.2 on the project and then upload "only software" I get: 

   "An upload is not possible due to incompatible configuration Target Drive unit_1 in the offline project differs form the target in the online project"

Installed Software:
* Tia Portal Version V15.1 Update 4

* Startdrive advanced update 3

* SINAMICS Startdrive G130, G150, S120, S150, SINAMICS MV, S210 Version V15.1 Update3

* Step 7 Proffesional Version V15.1 Update 4

* STEP 7 Safety Version V15.1 

What can we do?

How to integrate that S120 on a TIA 15.1? 

Thanks

Could be Tia Portal 16 + Stardrive 16 upd 4 the solution??

What does the readme for Startdrive 16 Upd 4 state was added?  How about Upd 3 / 2 / 1?  Do any of them add support for that firmware / service pack?  I do not know as I have avoided Startdrive because ... well for the same reason you are chasing updates to get support for firmware updates that solve process problems.

af_tds

Thanks

Could be Tia Portal 16 + Stardrive 16 upd 4 the solution??

I will check the readme, but by the way, I added a new S-120 on TIA Portal V16 with the last Startdrive and I can select the S120 5.2.3, meanwhile on Tia Portal V15.1 and startdrive the last supported is 5.2.

Pray for me

Oh yes, on 

https://support.industry.siemens.com/cs/ww/en/view/109782435 

says

• SINAMICS S120/S210: Support of new firmware V5.2 SP3"

 I hope it would run well, almost enough to have the S120 on the TIA Portal project and avoid using a S-120 GSD.

Dear Colleagues .

with Step 7 V16 and Startdrive advanced V16 update 4 I was able to upload from the device the S-120 CU320 2PN  with fw 5.2.3 and all its configuration and topology with no problem.

Thanks!