Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S1200, ktp400 Basic PN, Tia Portal

Created by: kijo at: 2/25/2014 10:55 AM (13 Replies)

Rating (0)

Thanks 0

Result pages:: |; 1 | 2; |

14 Entries

Entries per page: 10 | all

2/25/2014 10:55 AM	Rate (0)
kijo Posts: 79 Rating: (1)	HI, I am trying to connect S1200, KTP400 Basic ON and PC via LAN. They are all in same subnet conected trought local network with ethernet switch. I can see PLC and everything works OK, but I can't establish connection with KTP400 Panel. I was trying to manually specify an IP adress and obtain IP adress via DHCP but nothing doesn't work. This should be something on principe plug and play but I am loosing my time with this. Any sugesstions please?
kijo Posts: 79 Rating: (1)
Suggestion To thank Quote Answer

2/25/2014 11:09 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 10/10/2024 Posts: 8745 Rating: (1168)	Hello kijo, Perhaps this link might help: how can you transfer a WinCC (TIA Portal) configuration to an operator panel using Ethernet? Best regards, Wizard

Suggestion To thank Quote Answer

2/25/2014 12:22 PM	Rate (0)
kijo Posts: 79 Rating: (1)	Thanks for answer Wizard, but it still doesn't work. Under the accessible devices I see my panel and when I ping panel IP adrress everything is ok. When I click on panel to transfer he can't connect to host. Under the Tia portal I get this error messages: Connected to HMI_RT_1, Address MAC=00-1B-1B-2A-49-77., Going online: the HW configuration of the HMI_RT_1 was changed but it was not compiled and loaded yet. The shown diagnostics is possibly inconsistent or wrong., The target HMI_RT_1 in the offline project is different from the target in the online project (address 00-1B-1B-2A-49-77)., Going online: the HW configuration of the PLC_1 was changed but it was not compiled and loaded yet. The shown diagnostics is possibly inconsistent or wrong.,
kijo Posts: 79 Rating: (1)
Suggestion To thank Quote Answer

2/25/2014 12:58 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 10/10/2024 Posts: 8745 Rating: (1168)	Hello kijo, I guess you compile your HMI program. (Without errors?) Is the panel in transfer mode? Best regards, Wizard

Suggestion To thank Quote Answer

2/25/2014 1:09 PM	Rate (0)
kijo Posts: 79 Rating: (1)	I compiled my program without errors, it is simple test program not something complicated. My panel isn't in transfer mode (that is basic problem). When I click on panel transfer button, I just get message connecting to host, and nothing happens.
kijo Posts: 79 Rating: (1)
Suggestion To thank Quote Answer

2/25/2014 1:16 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 10/10/2024 Posts: 8745 Rating: (1168)	Hi, Check the transfer settings in panel? And the panel must be in transfer mode, when you want to download your project. Best regards, Wizard

Suggestion To thank Quote Answer

2/25/2014 1:39 PM	Rate (0)
kijo Posts: 79 Rating: (1)	Thanks for help Wizard, In Panel Control Panel/Transfer sesttings are this settings: Channel 1: Ethernet, and marked Enable Channel and Remote Control. Under Advanced/IP Address marked Obtain IP adress via DHCP (tried to specificied IP address manually but no diference) Under Mode, Communication link is half-duplex, marked Auto nagotiation, and NOT marked deactivate LLDP I don't see anything wrong there. Any idea?
kijo Posts: 79 Rating: (1)
Suggestion To thank Quote Answer

2/25/2014 1:51 PM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 10/10/2024 Posts: 8745 Rating: (1168)	Hello kijo, I would suggest to use a manual specified IP address. (in the same range as used PC) When you are in Advanced settings, can you go to tab 'device' Please enter an unique station name. Best regards, Wizard

Suggestion To thank Quote Answer

2/25/2014 3:27 PM	Rate (0)
kijo Posts: 79 Rating: (1)	I already try that but with no success :( I still can't go on transfer mode on my panel. If you or somebody else have any more idea I would appreciate. Thanks in advance.
kijo Posts: 79 Rating: (1)
Suggestion To thank Quote Answer

2/26/2014 8:16 AM	Rate (0)
Wizard Diamond Expert Joined: 4/24/2006 Last visit: 10/10/2024 Posts: 8745 Rating: (1168)	Hello kijo, What is the "Station name" you have specified in panel? Best regards, Wizard

Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on