Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

s5 to s7 conversion

Created by: ahsan1820 at: 8/15/2012 8:33 AM (6 Replies)

Rating (0)

Thanks 1

7 Entries

8/15/2012 8:33 AM	Rate (0)
ahsan1820 Posts: 119 Rating: (1)	I have a message ,during s5 to s7 conversion."NO xrf file available.blocks can not be stored according to their call".shown in the attached picture. As i know xrf is cross refrence file of s5 program. and i want to know that will the imprper storage of blocks will make any trouble for me. My conversion end without any warnings and errors. when i am compiling the AWL file in the "sources" of Step7 i is creating a converted source file but i have no blocks automatically generated at the "blocks" of step7,rather i have to copy them from source file and make OB and FC. Attachment s5.JPG (456 Downloads)
ahsan1820 Posts: 119 Rating: (1)
Suggestion To thank Quote Answer

8/17/2012 3:32 PM	Rate (0)
Simaticus Bronze Member Joined: 1/30/2007 Last visit: 6/3/2022 Posts: 262 Rating: (24)	Hi ahsan1820, that message means that the converter can't find the x-ref of the s5 blocks in the s5d file. Hence you will need Step5 to create the x-ref. Good luck

Suggestion To thank Quote Answer

8/18/2012 10:05 AM	Rate (0)
ahsan1820 Posts: 119 Rating: (1)	Thanks I have step 5 now please tellme how to create xref file from it ? [schnippschnapp]
ahsan1820 Posts: 119 Rating: (1)	Last edited by: O_Moderator at: 8/20/2012 10:34 AM new question was splitted to /tf/WW/en/Posts/79054#top
Suggestion To thank Quote Answer

8/20/2012 3:30 PM	Rate (0)
Simaticus Bronze Member Joined: 1/30/2007 Last visit: 6/3/2022 Posts: 262 Rating: (24)	Hi ahsan1820, you open your project using Step5 (V6.x or V7.x) and then open any of the blocks. I usually try OB1 which is the base of nearly every project, so i miss all the fun of searching blocks. After opening this block you'll see a F-key "x-ref", press it, a new menue of function keys opens including "create x-ref" or "generate" or something similar. (Sorry i just have to depend on memory, there's no system available to me currently). Now press f-key "vreate x-ref", wait a minute for the system to be done, and you got the x-ref the converter is needing to get its job done. You just need to leave the block unchanged (best advice use ESC), leave the S5 project and close Step5. Good luck

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Phantao1996

8/21/2012 2:23 PM	Rate (0)
ahsan1820 Posts: 119 Rating: (1)	after compiling the source file i am having the errors and warnings shown in the attachment please tell me its meaning?will this make any problem? Attachment untitled.JPG (453 Downloads)
ahsan1820 Posts: 119 Rating: (1)
Suggestion To thank Quote Answer

8/28/2012 3:13 PM	Rate (0)
SieMuzzy Posts: 59 Rating: (2)	I suggest a video for problems. If you send me your e-mail adress, ı may send you this video so this video can helps your both problems. the video is created screen shots Good luck.. Best Regards
SieMuzzy Posts: 59 Rating: (2)	Last edited by: O_Moderator at: 28.08.2012 18:01 contact data deleted
Suggestion To thank Quote Answer

8/29/2012 7:21 AM	Rate (0)
ahsan1820 Posts: 119 Rating: (1)	hi i have send you email in the private messages.
ahsan1820 Posts: 119 Rating: (1)
Suggestion To thank Quote Answer

|

Share this page:

Share this page on...

Follow us on