Skip to Content

Register Login

Industry Online Support

Technical Forum

Navigation

S7-1200 and HMI

Created by: Darius at: 7/11/2009 1:10 PM (10 Replies)

Rating (1)

Thanks 4

Result pages:: |; 1 | 2; |

11 Entries

Entries per page: 10 | all

7/11/2009 1:10 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	Hello all, Is there a possibility to connect HMI other than Basic series to S7-1200 PLC ? For example can I connect MP377 ? What driver in Flexible should I use ?
	Best regards, Darius
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Arunakat1

7/13/2009 9:52 AM	Rate (1)
Robster Gold Expert Joined: 5/28/2008 Last visit: 10/23/2024 Posts: 1343 Rating: (141)	Hi, try to use S7-300/400 driver in WinCC flex. Also Slot 1, Rack 0. The DB for Data Exchange in S7-1200 have to be non-symbolic.

Suggestion To thank Quote Answer

7/13/2009 10:04 AM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	Hi, I have no possibility to try that, but it would be nice to get response from users who tried it. What Siemens say about it ?
	Best regards, Darius
Suggestion To thank Quote Answer

7/13/2009 12:18 PM	Rate (0)
Denilson Pegaia Platinum Expert Joined: 9/23/2005 Last visit: 11/19/2024 Posts: 4353 Rating: (1454)	Hi, At this moment, the work around of Mr. Robstermust be take in acount: programming like a S7-300/400.
	Denilson Pegaia Siemens Industry Sector Technical Support
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users ritu

7/13/2009 12:24 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	Programmin without symbols is not a very good idea. Then I think better is to use Basic series with S7-1200 and if Basic series is not enought then better is to take S7-300
	Best regards, Darius
Suggestion To thank Quote Answer

7/13/2009 12:48 PM	Rate (0)
Robster Gold Expert Joined: 5/28/2008 Last visit: 10/23/2024 Posts: 1343 Rating: (141)	No, I didn't say to program non-symbolic. Let me try to explain: You can create function blocks or data block as symbolic or non-symbolic. In case of a DB the only different is, that in a non-symbolic DB you have the possibility to access with absolute adresses like DB1.DBX0.0 or DB1.DBD4 and so on. It's important for WinCC flex. There you have to enter absolute adresses. You have no access on a symbolic DB with WinCC flex. Anyway, in a non-symbolic DB you can also enter symbolic names and you can also have access to the symbolic name in programming. But pay attention to, that you have no possibility to use data type of LREAL in a non-symbolic DB or FB. I hope its clear now. regards

Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Berg

7/13/2009 2:09 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	It seems that we are talking about different things. I was wondering if I will se symbols in Flexible from Step-7 basic as I can see them from usual Step-7 project.
	Best regards, Darius
Suggestion To thank Quote Answer

7/13/2009 3:47 PM	Rate (0)
Robster Gold Expert Joined: 5/28/2008 Last visit: 10/23/2024 Posts: 1343 Rating: (141)	No, you can't see symbols because you can't implement a WinCC flex project in Step7 basic. You have to see it like S7-200 and WinCC flex. Two different independent programs.

Suggestion To thank Quote Answer

7/13/2009 9:59 PM	Rate (0)
Smurf Silver Member Joined: 9/28/2005 Last visit: 10/24/2024 Posts: 414 Rating: (28)	Robster Hi, try to use S7-300/400 driver in WinCC flex. Also Slot 1, Rack 0. The DB for Data Exchange in S7-1200 have to be non-symbolic. Hi All, This is also the answer I got last week from Siemens. I haven't found time to try it yet.
	Smurf "The only difference between a problem and a solution is that people understand the solution."
Suggestion To thank Quote Answer

1/12/2010 3:58 PM	Rate (0)
Darius Platinum Member Joined: 9/28/2005 Last visit: 11/5/2024 Posts: 2957 Rating: (242)	Hello, I can confirm that with KTP1000 PN and WinCC Flexible 2008 Advanced it is working by using S7-300/400 driver with CPU in rack 0, slot 1.
	Best regards, Darius
Suggestion To thank Quote Answer
This contribution was helpful to 1 thankful Users Berg

|

Share this page:

Share this page on...

Follow us on